ClearSpan Super Moo-Tel Building 38' Wide Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 47

background image

CLEARSPAN

™

SUPER MOO-TEL

6

Revision date: 03.16.12

Interior Rafter

End Rafter

Cable

Assemblies

Purlin

38' on-center

Frame length of your building may differ from what is shown.

ClearSpan

™

Super Moo-Tel Building

OVERVIEW

This section describes assembling your Super Moo-Tel

building. For details of each assembly procedure, consult

the Quick Start Guide and the individual sections of these

instructions. See illustration below to identify main parts of

shelter.
1. Layout the site and identify the required parts for each

assembly procedure.

2.  Assemble all rafters.
3.  Assemble and anchor the frame.
4.  Cut, assemble, and install all cables.
5.  Install end wall framing.
6.  Prepare and install the main cover.
7.  Attach end panels and cut door openings.
8.  Install the door or doors according to the

instructions included with

those components.

The instructions that follow describe assembling all rafters

and then constructing the frame. Depending on the number

of individuals assisting with the construction, it may be best

and more efficient to have someone assemble the rafters

and others assemble the frame as rafters are completed.

Other factors to consider during the assembly, especially

for buildings longer than 60', include:
•  Amount of work/assembly area
•  Available lifts and work platforms
•  Number of assistants

«
...
4
5
6
7
8
...
»

Содержание Super Moo-Tel Building 38' Wide
















































Отзывы:

Нет отзывов

Похожие инструкции для Super Moo-Tel Building 38' Wide

Бренд: Redpath Страницы: 25

Бренд: ClearSpan Страницы: 25

Бренд: BROWIN Страницы: 2

Бренд: BROWIN Страницы: 14

Greenhouse Mini

Бренд: lahe Страницы: 29

Бренд: oGrow Страницы: 31

Бренд: GARDY SHELTER Страницы: 98

Бренд: LAMS Страницы: 30

AeroGarden Extended Season

Бренд: AeroGarden Страницы: 8

Бренд: Black Orchid Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды