ClearSpan Super Moo-Tel Building 38' Wide Скачать руководство пользователя страница 18

Страница: 18 / 47

CLEARSPAN

™

SUPER MOO-TEL

Revision date: 03.16.12

INSTALL THE MAIN COVER SIDE STRAPS

The side straps wrap around slits in the conduit pocket. The

strap ends of each strap are then fed into each side ratchet

(attached to the purlin brackets on the inside of the frame)

and slightly tightened.

Required parts and tools:
• 2" yellow bulk strap
• Tool to cut slits in cover conduit pockets

Complete these steps to install the side straps:
1. Move to one side ratchet (attached to the inside of the

frame) and cut a slit in the

conduit pocket

above the

conduit and

in line with the ratchet

Photos below show using a utility knife to cut a slit

above the conduit, which is inside the conduit pocket.

NOTE:

When cutting the slit in the pocket for the strap,

do not cut the main cover; cut only the pocket material.

2. Using the ratchet and conduit positions as guides,

measure and cut a tie down strap from the bulk yellow

strap that shipped with the building. Straps run from the

ratchet, up and around the cover conduit, and back to

the ratchet.

NOTE:

Cut the strap length so that the strap can

wrap around the cover conduit and both ends can be

inserted into the ratchet.

3. After cutting the strap, feed one end through the slot

in the cover pocket, around the conduit, and align the

strap ends.

4. Feed both ends through the slot in the center drum

of the ratchet and slightly tighten the ratchet.

Do not

tighten completely at this time.

5. Repeat the previous steps to install and slightly tighten

the remaining straps.

6. After installing all side straps and with the cover

centered evenly on the frame, trim the hem area of the

main cover for the roll-up side.

Cover Conduit

Conduit Pocket

Cover Conduit

Cover

Roll-up

Side

Strap

STEP 1

Содержание Super Moo-Tel Building 38' Wide
















































Результаты поиска

Содержание Super Moo-Tel Building 38' Wide

Отзывы:

Похожие инструкции для Super Moo-Tel Building 38' Wide

Бренды по названию

Популярные бренды

ClearSpan Super Moo-Tel Building 38' Wide, Инструкция по сборке

Результаты поиска

Содержание Super Moo-Tel Building 38' Wide

Отзывы:

Похожие инструкции для Super Moo-Tel Building 38' Wide

Бренды по названию

Популярные бренды