ClearSpan PB03000R5 Скачать руководство пользователя

Страница: 16 / 23

CLEARSPAN

™

GARAGES

Revision date: 09.14.10

INSTALL MAIN COVER (continued)

2. After assembling the cover conduits, locate the main

cover and unfold it on a clean, smooth surface near the

frame.

NOTE:

When handling the cover and setting it in

position, do not pull on the end straps. They will pull out

of the cover. Unfold the cover with the inside surface

facing up.

3. Locate the cover end straps and align these with the

front and back of the shelter.

4. Insert the cover conduits into pockets of the cover.

NOTE:

Shelter shown above may differ in length from

the actual model.

5. To pull the cover over the frame, attach ropes to both

ends of the cover conduit farthest from the frame. Wrap

the rope around the conduit a few times to prevent it

from slipping off.

Cover Conduits

Cover

Ends w/

Strapping

Main Cover Pocket

NOTE:

Depending on the length of the cover it may

be necessary to attach additional ropes to the cover

conduit between the end ropes by cutting a small

opening in the cover pocket and tying the rope around

the conduit. DO NOT cut through the cover.

Cut

through the conduit pocket only.

6. With all ropes attached to the cover conduit, lift the

conduit and carry the cover toward the base of the

frame.

7. Toss the ropes over the frame and pull the cover into

position. One person is required at each rope.

8. Center the cover front to back and side to side.
9. Using the straps in the main cover, secure the ends

of the main cover to the ratchets attached to the end

panel conduit.

Do not tighten completely at this time.

10. Locate the 1" wide black strapping (#103620B). If the

strap was shipped in bulk, cut pieces about 3' long.

If the strap was shipped pre-cut in 3' lengths, place a

length of strap at each side ratchet.

11. Cut a slit in the cover conduit pocket at each side rafter

position. Insert a section of strap through the slit and

around the cover conduit.

NOTE:

DO NOT cut through the main cover.

Cut

through the conduit pocket only.

Photos may show a

different rafter, procedures are the same.

12. Thread the strap ends into the ratchet and slightly

tighten.

NOTE:

It may be necessary to remove excess strap if it

binds up in the ratchet.

13. Repeat the steps for the remaining ratchets.
14. Using additional help (if needed) tighten the main cover

beginning with the ratchets along the side of the frame.

15. After the side ratchets are tightened, return to the end

panel ratchets and tighten the bonnet straps of the

cover.

NOTE:

Loosen the ratchets if needed to remove

excess strap and retighten. Loosen all ratchets if

needed to reposition the main cover on the frame and

retighten the ratchets.

16. Read the care and maintenance section that follows.

Base Rail

Main Cover

Содержание PB03000R5
























Результаты поиска

Содержание PB03000R5

Отзывы:

Похожие инструкции для PB03000R5

Бренды по названию

Популярные бренды

ClearSpan PB03000R5, Руководство пользователя

Результаты поиска

Содержание PB03000R5

Отзывы:

Похожие инструкции для PB03000R5

Бренды по названию

Популярные бренды