8
Unpack your Furnace and insure that there is no shipping dam-
age. If damage exist, please contact your dealer immediately.
Your furnace will require some assembly before operation. All
needed hardware and components for the following assemblies
are included within the parts boxes inside the furnace and in
the ash pan. Read and follow these instructions for proper fur-
nace assembly.
DOOR HANDLES
Insert door handle into door. From rear side of door, place a
1/2” washer over the threaded part of the handle, then attach
the lock nut. Tighten the nut, then back off 1/4 turn to allow
free operation of the handle.
Follow these same directions for the ash door handle assembly.
(2) Door Handle
(2) 1/2” Washer
(2) 1/2” Lock Nut
ASH DOOR SPIN DRAFT
Screw the spin draft onto the 3/8” x 2-1/2” carriage bolt. Th
en screw the spin draft and bolt into the ash door allowing ap-
proximately 1/2” of the bolt to stick through the back side of
the ash door. Secure the bolt in place with the 3/8”-16 lock nut.
For Canadian Installations, this spin draft is replaced by a
block-off plate and must not be tampered with or removed to
increase the fi ring rate of the furnace.
(1) Spin Draft
(1) 3/8-16 Carriage Bolt
(1) 3/8-16 Lock Nut
FUEL & ASH DOOR LATCH
With two 1/4-20 x 3/4 hex bolts each, attach the door latches
to the door latch mounting brackets on the left side of the door
frames as illustrated. Th
e slots in the brackets and latches are
for door seal adjustment. Make the proper adjustments, then
tighten the nuts. Th
e door’s gasket should be snug against the
door frame on the furnace.
Feed Door
Illustration
Ash Door
Illustration
(1) Feed Door Latch
(1) Ash Door Latch
(4) 1/4-20 x 3/4 Hex Bolt
(4) 1/4-20 Kep Nut
BRACKET
SHAKER GRATE HANDLE
Insert the Shaker Rod into the hole on the ash door frame as
shown. Th
en attach the Shaker Bracket to the front of the fur-
nace using two 1/4-20 x 3/4” Hex Bolts and two 1/4-20 Lock
Nuts. Next, insert the shaker Rod into the bracket and attach
to the shaker grate bar using the 1/4-20 x 1” Hex Bolt and a
1/4-20 Lock Nut. Th
e bolt and nut retaining the shaker bar and
rod should be left loose to allow free movement of the grates.
(1) Shaker Rod
(1) Shaker Bracket
(1) 1/4-20 x 1” Hex Bolt
(2) 1/4-20 x 3/4” Hex Bolt
(3) 1/4-20 Lock Nut
FRONT
SMOKE CURTAIN
SMOKE CURTAIN
CLIP
NUT
BOLT
1/4-20 NUT
SMOKE CURTAIN
CLIP
1/4-20 x 1-1/4
CARRIAGE BOLT
SMOKE CURTAIN
SMOKE CURTAIN
Using two 1/4-20 x 1-1/4” Carriage bolts, the smoke curtain
clips and two nuts, attach the smoke curtain in place above the
Fuel Feed Door as shown below. Aft er installation, the smoke
curtain should swing freely back into the furnace.
(1) Smoke Curtain
(2) Smoke Curtain Clips
(2) 1/4-20 x 1-1/4 Carriage Bolt
(2) 1/4-20 Kep Nut
FURNACE ASSEMBLY INSTRUCTIONS