Classe Audio CP-800 Скачать руководство пользователя страница 29

Страница: 29 / 54

Brightness

The

Brightness

setting of the CP-800 touchscreen has three possible values:

low,

medium,

and

high

. Select the setting you prefer. A

high

brightness setting usually

works best in brightly-lit rooms; you may find that a lower setting is less visually

intrusive under more subdued lighting conditions.

Timeout

If you prefer listening to music in a dimly-lit or darkened room, you may

find even the

low

brightness setting of the display somewhat distracting. You

can essentially turn off the touchscreen by reducing the

timeout

value of the

backlighting so as to turn it off entirely after a period of inactivity that you

may select. In this context, activity refers to any use of the user interface. This

includes hard buttons, the touchscreen, and the remote control.

For example, if you reduce the timeout to its minimum setting, the backlighting

illuminates the display as soon as you interact with any of the CP-800 controls,

and remains lit for only three seconds – just long enough for you to check a

setting. If you continue to use any of the controls (at least once every three

seconds), the display remains lit. After three seconds of inactivity on your part,

the backlight extinguishes itself, essentially turning off the touchscreen.

If you prefer the display of the CP-800 to remain on whenever not in

Standby

mode, select the

Never

timeout option. The lamp in the touchscreen display is

designed for harsh automotive environments and will give you many years of

reliable operation. If you plan to leave the unit on continuously, however, we

recommend that you keep the timeout delay set to less than one minute.

NOTE: setting the brightness to a lower setting does not increase

the life of the lamp.

Volume Setup

Touching the

Volume Setup

button in the System Setup menu opens the

Volume Setup page, as shown below. The volume knob is used to make all

volume setup adjustments.

Volume Setup allows you to:

• set a maximum volume level;

• choose an initial volume level for the system whenever the CP-800 is

brought out of Standby;

• customize the behavior of the mute control.

Содержание CP-800























































Результаты поиска

Содержание CP-800

Отзывы:

Бренды по названию

Популярные бренды

Classe Audio CP-800, Руководство пользователя

Результаты поиска

Содержание CP-800

Отзывы:

Бренды по названию

Популярные бренды