Classe Audio CP-800 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 54

background image

20

Step 3

Connect source components to the CP-800 rear panel.

If necessary, refer to the

Rear Panel

section in this manual for a detailed

description of each connector found on the rear panel. Your local Classé dealer

can also provide useful suggestions for what source components you should add

to your system and guidance in setting them up.

Make sure you keep a detailed record of the rear panel

connectors that you used while connecting the source

components!

You’ll need to know what connector(s) each source is attached to when you enter

the setup menus. An

Installation Worksheet

is included at the end of this manual

to assist you.

NOTE: In the CP-800 default settings, sixteen rear panel inputs

are associated with corresponding source selections within the

Source Setup menu. Since most users will have fewer sources

connected, the Source Selection page(s) can be simplified by

unchecking the Enable Source box for each unused input. Doing so

removes the corresponding Source button from the Source Selection

page. See the Menu System section for details.

Step 4

Connect the power amplifier(s) to the CP-800 rear panel.

Important!

Verify that the power amplifier(s) is plugged in but powered

OFF before connecting to the CP-800!

We recommend using high quality cables with XLR connectors.

NOTE: These pin assignments are consistent with the standards

adopted by the Audio Engineering Society. Refer to the operating

manuals of your balanced-input power amplifiers to verify that the

pin assignments of their input connectors correspond to the CP-

800. If you are using Classé amplifiers, this note does not apply.

If needed, the pin assignments of the XLR-type male output

connectors are:

Pin 1: Signal ground

Pin 2: (non-inverting)

Pin 3: Signal – (inverting)

Connector ground lug: chassis ground

«
...
18
19
20
21
22
...
»

Содержание CP-800























































Отзывы:

Нет отзывов

Похожие инструкции для CP-800

Бренд: D.A.S. Страницы: 28

Бренд: d&b audiotechnik Страницы: 28

Бренд: FLC ELECTRONICS Страницы: 9

C Series C 16 4

Бренд: Lab.gruppen Страницы: 2

Бренд: Crown Страницы: 6

Amplifier 800-40

Бренд: Raymer Страницы: 5

Бренд: XINDAK Страницы: 10

Бренд: AMERITRON Страницы: 19

Бренд: D.W. Fearn Страницы: 37

Бренд: Marantz Страницы: 46

Power Amplifier Servo 550

Бренд: Samson Страницы: 2

Бренд: UNIELECTRONIC Страницы: 12

Acoustimass 5 Series III

Бренд: Bose Страницы: 22

The Prelude PC-200

Бренд: Harman Kardon Страницы: 6

Бренд: ATEN Страницы: 2

Бренд: Luxman Страницы: 24

Бренд: ifi Страницы: 35

Contractor Precision CPS2.12

Бренд: Electro-Voice Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды