Classe Audio CP-800 Скачать руководство пользователя

Страница: 25 / 54

From the System Setup menu, you can:

• tailor your inputs to your particular source components

• configure the system to take best advantage of your loudspeakers

• tailor the display to your preferences

• set volume control parameters

•

enable and setup the Parametric EQ

• setup Tone Control parameters

• view the unit’s Network IP address/status and settings

•

choose Remote F key functions

•

assign DC triggers

•

teach IR commands

Source Setup

Each of the 18 source buttons supported by your CP-800 can be customized in

several ways to enhance system performance or to simplify operation. The source

select page is dynamic in that it shows up to nine sources on a single page. If six

or fewer are enabled, then the page shows six somewhat larger buttons and if

three or fewer are enabled, it shows only three large buttons. Press the button for

the source you want to set up. The setup page for that source includes buttons

for assigning the input connector(s) and naming the source, choosing a default

speaker configuration, setting an input offset, selecting the Pass-Thru feature or

choosing the Digital Bypass path.

Enable Source

This check box activates/deactivates source buttons. If the

Enable Source

box is

checked, then the source is enabled. If the Enable Source box is NOT checked,

then the source is considered not enabled and is so identified on the Source

Selection page.

Disabling unused sources is a good way to simplify source selection. The

Source Selection page is dynamic, adjusting the number and size of buttons to

correspond to the number that are actually being used or enabled. The buttons

arrange themselves into groups of either three, six or nine buttons on the Source

Selection page.

Input Connector

Choose the input connector(s) to be associated with this source button. Any

source button may be associated with any input connector(s). Also, multiple

source buttons may be assigned to the same connector(s).

Содержание CP-800























































Результаты поиска

Содержание CP-800

Отзывы:

Похожие инструкции для CP-800

Бренды по названию

Популярные бренды

Classe Audio CP-800, Руководство пользователя

Результаты поиска

Содержание CP-800

Отзывы:

Похожие инструкции для CP-800

Бренды по названию

Популярные бренды