Clarke X-Pro CAT202 Скачать руководство пользователя | Manualshive

Страница: 10 / 32

background image

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Use only clean, dry, regulated compressed air as a power source.

Air compressors used with the tool must comply with the appropriate
European Community Safety Directives.

A build-up of moisture or oil in the air compressor will accelerate wear and
corrosion in the tool. ensure any moisture is drained from the compressor daily
and the inlet filter is kept clean.

If an unusually long air hose is required, (over 8 metres), the line pressure or the
hose inside diameter may need to be increased.

The air hose must be rated at least 150% of the maximum operating pressure of
the air tool.

Never exceed the maximum operating pressure for the air tool. It is
recommended that air pressure to this tools does not exceed 90 psi at the tool
when running. Higher pressures and unclean air will shorten the life of an air
tool due to faster wear and is a possible safety hazard.

«
...
8
9
10
11
12
...
»

Содержание X-Pro CAT202

































Отзывы:

Нет отзывов

Похожие инструкции для X-Pro CAT202

Бренд: Nederman Страницы: 120

Бренд: ZALMAN Страницы: 7

Бренд: GARANT Страницы: 100

Бренд: GE Страницы: 3

Бренд: TMG Страницы: 19

Start-It VEC025MB

Бренд: Vector Страницы: 8

Бренд: Pulsar Страницы: 8

Бренд: Robust Страницы: 44

Бренд: Wacker Neuson Страницы: 54

KF**-CRG2-1.D Series

Бренд: Pepperl+Fuchs Страницы: 38

Бренд: Worldwide Страницы: 2

Бренд: Parkside Страницы: 80

Бренд: Neilsen Страницы: 2

Бренд: YATO Страницы: 64

Бренд: Oemtools Страницы: 4

Бренд: BGS technic Страницы: 8

Бренд: Moser Systemelektrik Страницы: 6

Бренд: Varan Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды