Clarke X-Pro CAT202 Скачать руководство пользователя | Manualshive

Страница: 11 / 32

background image

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

BEFORE USE

1. Remove the plastic blanking plug from the air inlet connection.

2. Pour 2-3 drops of CLARKE airline oil into the oil filling port. This should be

done regardless of whether or not a lubricated air supply is to be used.

3. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of any air tool.

4. Connect a suitable hose as shown

or use the snap connector
supplied to connect directly to the
hose.

• PTFE tape may be useful for

sealing threaded connections

5. Connect the other end of the hose

to the compressor.

6. Turn on the air supply and check

for air leaks. Rectify any found
before proceeding.

7. If using a mini oiler, place a sheet of paper next the exhaust port and hold

the throttle open for approximately 30 seconds. The oil volume is correctly
set when a light stain of oil can be seen on the paper. Excessive oil should
be avoided.

8. Your air tool is now ready for use.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR
COMPRESSORS AND COMPRESSED AIR SUPPLY.

«
...
9
10
11
12
13
...
»

Содержание X-Pro CAT202

































Отзывы:

Нет отзывов

Похожие инструкции для X-Pro CAT202

Бренд: Earlex Страницы: 20

Бренд: Palmgren Страницы: 20

Бренд: WAGNER Страницы: 12

Бренд: tacwise Страницы: 12

Бренд: Hama Страницы: 36

AXMINSTER Model Engineer Series

Бренд: Sieg Страницы: 28

Бренд: Hilti Страницы: 191

Бренд: Tapco Страницы: 2

Бренд: OEM Tools Страницы: 8

Бренд: Greenlee Страницы: 16

Бренд: Baileigh Industrial Страницы: 20

Бренд: Worcraft Страницы: 32

Бренд: Yokota Страницы: 7

Бренд: Ryobi Страницы: 22

Бренд: Wood-mizer Страницы: 48

Aliaxis CLAMP63

Бренд: FRIATEC Страницы: 12

Бренд: Somogyi Страницы: 16

Бренд: Yokota Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды