background image

19. DO NOT STAND ON THE MACHINE. Serious injury could occur if the machine is tipped

over. Do not store materials above or near the machine such that it is necessary to
stand on the machine to get to them.

20. NEVER operate a machine when under the influence of alcohol, drugs or

medication.

21. ALWAYS ENSURE THAT ADEQUATE LIGHTING is available. A minimum intensity of 300

lux should be provided. Ensure that lighting is placed so that you will not be working
in your own shadow.

ADDITIONAL SAFETY RULES FOR DRILL PRESSES

WARNING:

THIS MACHINE MUST NOT BE MODIFIED,  OR USED FOR ANY PURPOSE OTHER

THAN THAT FOR WHICH IT IS DESIGNED.

1.

IMPORTANT: You should not operate this machine unless you are thoroughly familiar
with drilling machines and drilling techniques. If there is any doubt whatsoever, you

should consult a qualified person.

2.

Do not operate the machine until it is completely assembled, and you have read, and
understood. this entire manual

3.

Ensure the proper electrical regulations are followed, and that the machine is properly
earthed.

4.

Before switching the machine ON, ALWAYS:-

a.

Ensure all chuck keys, spanners and wrenches are removed from the machine.

b.

Examine the setup carefully, ensuring that the workpiece is perfectly secure.

c.

Ensure your clothing is properly adjusted.

5.

Make all adjustments with the power OFF.

6.

Always use the correct drilling speeds for the drill size, and the type of material being
drilled (see page 15).

7.

NEVER leave the drill unattended whilst it is running. Turn the machine OFF and do not
leave until it has come to a complete stop.

8.

When you have finished with the machine, always remove and store the drill bits.

9.

CAUTION: This Drill Press is designed for use with Drill Bits and Morticing attachments
ONLY. The use of other cutting tools or accessories could be hazardous.

10.  ALWAYS use clamps, or a drill vice bolted to the table, to hold the work. It should NEVER

be held in bare hands.

5

Содержание Metalworker CDP301B






















Отзывы: