Clarke DP6H-APKA60 Скачать руководство пользователя | Manualshive

Страница: 35 / 49

background image

Page 35 of 49

3.5.2

Checking

Drive

Belt

Tension

and

Adjustment

All drive belts must be adequately tightened to secure
that both the engine water pump and battery charging
alternator (when fitted) are operating efficiently.
Refer to

Figures #28A,28B, 28C, 28D.

Figure #28A – DP6H

Figure #28B – DQ6H

Figure #28C – DR8H / DS0H / DT2H

Figure #28D – DT2H

To adjust Belt Tension:

Check belt tension:
- Give at arrow must be 0.4” - 0.6” (10-15mm).
To increase tension of the water pump driving belts:

- Loosen alternator or belt tensioner mounting
bolts A and B.

  - Adjust to proper belt tension.
  - Tighten mounting bolts A and B.

3.5.3 Speed Switch (when supplied)

Overspeed  is  defined  as  120%  of  rated  speed  for
engines  rated  from  1470  through  2600  rpm.    In  the
event  of  an  engine  overspeed,  the  speed  switch
signals  the  main  pump  controller and  also  affects  an
engine  shutdown.  The  OVERSPEED  RESET
(

Figure# 9

) switch is included on the instrument

panel.  Should  an  overspeed  condition  occur,
investigate the cause and make necessary corrections
before  placing  engine  back  in  service.  The
OVERSPEED  RESET  must  be  manually  lifted  for
two (2) seconds to reset.

NOTE:    This  reset  operation  must  be
completed  to  allow  a  restart.  If  not,  the
engine  will  not  start  thru  the  main  pump
controller or manually.

OVERSPEED VERIFICATION

Hold  the  OVERSPEED  VERIFICATION  switch  in
the  “up”  position.  This  will  provide  the  main  pump
controller  with  an  overspeed  signal  and  engine
shutdown  at  67%  of  the  set  overspeed  RPM.    Start
the  engine  via  the  main  pump  controller;  the  speed
switch  will  generate  an  overspeed  signal  and
shutdown protecting both the engine and pump.

EXAMPLE

Rated Speed: 1760 RPM
Overspeed Shutdown: 2112 RPM (120% of
1760 RPM)
Verification Shutdown: 1410 RPM (67% of
2112 RPM)

CAUTION-

after verification of overspeed, lift the

OVERSPEED  RESET  switch  for  two  (2)  seconds
and  reset  the  main  pump  controller  to  re-instate
normal operation of the engine and speed switch.

Refer  to  Engineering  Technical  Bulletin  –  ETB003,
part  number  C133407,  on  the

www.clarkefire.com

website for adjusting the overspeed setting for range
rated engines.

B

B
A

A

B
A

«
...
33
34
35
36
37
...
»

Содержание DP6H-APKA60


















































Отзывы:

Нет отзывов

Похожие инструкции для DP6H-APKA60

Бренд: Beta Marine Страницы: 88

Бренд: Calpeda Страницы: 48

HP525 EFI Bravo Sterndrive Series

Бренд: Mercury Racing Страницы: 147

Бренд: Deutz Страницы: 37

Бренд: ACDC Страницы: 20

Бренд: Kober Страницы: 112

Бренд: Volvo Penta Страницы: 20

Бренд: Volvo Penta Страницы: 35

Бренд: Volvo Penta Страницы: 45

Бренд: Volvo Penta Страницы: 50

Бренд: Volvo Penta Страницы: 68

Бренд: Volvo Penta Страницы: 74

Бренд: SSANGYONG Страницы: 14

Бренд: DANA Страницы: 3

Бренд: ST Страницы: 281

Бренд: HELIX Страницы: 18

Бренд: Ingersoll-Rand Страницы: 127

Бренд: Wood-mizer Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды