manualshive.com logo in svg

Clarke CMS250S, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke CMS250S Скачать руководство пользователя страница 15

15

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

DIFFERENT SAW CUTS

VERTICAL STRAIGHT CROSS CUT

1. Release the table mitre lock by 

twisting the handle anticlockwise.

2. Press and hold the latch down.

3. Move the arm so that the pointer 

lines up with the 0° position on the 
scale.

4. Release the latch to re-secure the 

mitre lock.

5. Release the slide rail lock, and 

push the saw head back to the 
rear position.

6. Retighten the slide rail lock.

7. Place the wood to be cut against 

the fence.

8. Take hold of the operating handle 

and press and hold the blade 
guard release lever to release the 
head.

9. Squeeze the trigger switch to start 

the saw.

10. Lower the head, allowing the 

blade to cut through the timber 
and enter the kerf plate.

•

Allow the blade to cut freely. Do 
not force the tool.

11. After completing the cut, release 

the trigger and return the head to 
its upper rest position.

Содержание CMS250S





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды