Clarke CMS250S Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Clarke CMS250S Скачать руководство пользователя страница 10

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

LOCKING / RELEASING THE SAW HEAD

1. Press down slightly on the

operating handle.

•

Pull out the head lock pin to
release the arm for cutting.

•

Push the pin back in to secure the
arm for lifting.

2. Gently release the downward

pressure on the operating handle
and allow the head to rise to its full
height.

FITTING THE WORK CLAMP

1. Loosen the clamp support

thumbscrew.

2. Slide the work clamp post into one

of the clamp supports on either
side of the saw.

3. Adjust the clamp to suit the

workpiece.

4. Tighten the thumbscrew to secure

the work clamp.

SETTING THE WORK SUPPORTS

1. Loosen the work support securing

screw.

2. Extend the work supports as

required.

3. Secure them in place by

tightening the work support
securing screw.

4. The work support incorporates a

hinged backstop which can be
raised if required.

«
...
8
9
10
11
12
...
»

Содержание CMS250S





























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды