manualshive.com logo in svg

Clarke C2MS210MP, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke C2MS210MP Скачать руководство пользователя страница 4

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

4.

Remove any adjusting key or wrench before turning the power tool on

. A 

wrench or a key left attached to a rotating part of the power tool may 
result in personal injury.

5.

Do not overreach. 

Keep proper footing and balance at all times. This 

enables better control of the power tool in unexpected situations.

6.

Dress properly. 

Do not wear loose clothing or jewellery. Keep your hair, 

clothing and gloves away from moving parts. Loose clothes, jewellery or 
long hair can be caught in moving parts.

7.

A laser beam

 can cause serious eye injury. Never look into the laser outlet.

POWER TOOL USE AND CARE

1.

Do not force the power tool. 

Use the correct power tool for your 

application. The correct power tool will do the job better and safer at the 
rate which it was designed.

2.

Do not use the power tool if the switch does not turn it on and off. 

Any 

power tool that cannot be controlled with the switch is dangerous and 
must be repaired.

3.

Disconnect the plug from the power source before making any 
adjustments, changing accessories, or storing power tools.

 Such preventive 

safety measures reduce the risk of starting the power tool accidentally.

4.

Store idle tools out of the reach of children and do not allow persons 
unfamiliar with the power tool or these instructions to operate the power 
tool. 

Power tools are dangerous in the hands of untrained users.

5.

Maintain power tools

. Check for misalignment or binding of moving parts, 

breakage of parts and any other condition that may affect the power 
tools operation. If damaged, have the power tool repaired before use. 
Many accidents are caused by poorly maintained power tools.

6.

Keep cutting tools sharp and clean. 

Tools with sharp cutting edges are less 

likely to bind and are easier to control.

7.

Use the power tool and accessories in accordance with these instructions 
and in the manner intended, taking into account the working conditions 
and the work to be performed

. Use of the power tool for operations 

different from intended use could result in a hazardous situation.

ADDITIONAL SAFETY RULES FOR MITRE SAWS

1.

Make sure

 all locking knobs and clamp handles are tight before starting 

any task.

Содержание C2MS210MP

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды