Clarke C2MS210MP Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

Clarke C2MS210MP Скачать руководство пользователя страница 12

12

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ADJUSTMENTS

CHECK AND ADJUST THE MITRE POINTER

The saw can be set in a number of positions as determined by the mitre
locking mechanism but the pointer should read zero when making straight
cuts and remain true for other angles selected.

1. If the pointer does not indicate

zero on the mitre scale, loosen the
pointer securing screw and adjust
it as necessary.

CHECK AND ADJUST THE 90 DEGREE ANGLE STOP

1. Loosen the bevel clamp handle.

2. Press the saw head to the side to

ensure it is fully vertical and
tighten the bevel clamp handle.

3. Pull down the operating handle

until the blade just enters the kerf
plate.

WARNING: MAKE SURE THAT THE SAW IS SWITCHED OFF AND UNPLUGGED
FROM THE MAINS SUPPLY BEFORE PERFORMING ANY ADJUSTMENTS.

«
...
10
11
12
13
14
...
»

Содержание C2MS210MP

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды