Clarke 7330347 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

Clarke 7330347 Скачать руководство пользователя страница 15

15

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

8. Pull the starting handle lightly until

you start to feel resistance and
then pull up sharply to start the
power washer.

NOTE:

You may have to do this

more than once.

.

9. Once the engine has warmed up,

set the choke lever to the ‘RUN’
(right) position.

USING THE POWER WASHER

1. Pull the trigger on the gun to start water flow.

• Stand on a stable surface and grip the gun/spray wand firmly with

both hands.

• Expect the gun to kick when the trigger is pulled.

2. Release the trigger to stop water flow.

NOTE:

The power washer will automatically go into bypass mode, In

bypass mode, the pump recirculates the water because the
trigger of the spray gun is not being pulled. If unit is left in bypass
mode for more than two minutes, the water temperature will rise

WARNING: ONCE THE POWER WASHER HAS STARTED, RELEASE THE
STARTING HANDLE SLOWLY TO AVOID INJURY/DAMAGE AS IT WHIPS
BACK.

«
...
13
14
15
16
17
...
»

Содержание 7330347

































Отзывы:

Нет отзывов