Clarke 6261525 Скачать руководство пользователя страница 11

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

• For positive earth vehicles, connect the NEGATIVE (BLACK) lead and 

clamp from the battery charger to the NEGATIVE terminal on the 
battery. Connect the POSITIVE (RED) lead and clamp to the vehicle 
frame or engine block away from the battery.

DO NOT

 connect the lead to ancillary engine components.

6. Where appropriate we recommend that the non-earthed lead on the 

battery is disconnected prior to charging. It is possible that damage may 
occur to the vehicle’s electronic equipment.

7. When charging is completed, switch off the charger. Remove the leads 

and clamps in the reverse sequence taken in the relevant step 5.

8. A marine (boat) battery must be removed and charged on shore. To 

charge it on board requires equipment specially designed for maritime 
use.

CONNECTING TO A BATTERY REMOVED FROM THE VEHICLE

1. Make sure that you know the polarity of the battery posts.

2. Identify the voltage of the battery to be charged (12v or 24v) and attach 

the POSITIVE (RED) lead to the appropriate terminal on the rear of the 
charger.

3.

ALWAYS

 remove the grounded (earth) terminal from the battery first, 

making sure that all electrical accessories in the vehicle are switched off to 
prevent sparking before removing the battery from the vehicle.

4. Clean the battery terminals. Be careful to prevent battery electrolyte from 

coming in contact with your eyes.

5. Except for sealed units, add distilled water to each cell until the battery 

acid reaches the level specified by the battery manufacturer. 

• This helps drive unwanted gas from the cell. Do not overfill. For a battery 

without cell caps, consult the manufacturer's instructions.

6. Follow all the battery manufacturer's specified precautions: for example, 

removing or not removing cell caps while being charged, and 
recommended rates of charge.

7. Connect the POSITIVE (RED) lead and clamp to the POSITIVE post on the 

battery.

8. Connect the NEGATIVE (BLACK) lead and clamp at arms length to the 

NEGATIVE post on the battery.

9. When you disconnect the charger/starter from the battery,

 ALWAYS

 do it in 

the opposite order to the sequence of connection and remove the first 
connection at arms length from the battery.

Содержание 6261525

























Отзывы: