background image

10   | 

www.

cistermiser

.co.uk

Configuring sensor range

Point the ICU at the sensor and press the

 1

 

 

sensor range button (the sensor blinks green).

Decrease or increase the sensor range by pressing 
the

and

buttons respectively. The sensor blinks 

red when the min or max value is reached.

Press the 

 button to check the sensor range 

setting – the sensor displays the current setting by 
flashing green, see table.

Save setting and exit ICU configuration mode by 
pressing the

button.

Exit without saving by pressing the

button.

Configuring run-on time

Point the ICU at the sensor and press the 

4

 

 

run-on time button (the sensor blinks green).

Decrease or increase the run-on time by pressing 
the

and

buttons respectively. The sensor blinks 

red when the min or max value is reached.

Press the 

 button to check the run-on time 

setting – the sensor displays the current setting by 
flashing green, see table.

Save setting and exit ICU configuration code by 
pressing the

button.

Exit without saving by pressing the

button.

Configuring the 12hr hygiene  
rinse cycle

Point the ICU at the sensor and press the 

5

 

 

 

12hr hygiene rinse button (the sensor blinks green).

Decrease or increase the hygiene rinse time by 
pressing the

and

buttons respectively. The 

sensor blinks red when the min or max value is 
reached.

Press the 

 button to check the hygiene rinse 

time setting – the sensor displays the current 
setting by flashing green, see table.

Save setting and exit ICU configuration mode by 
pressing the

button.

Exit without saving by pressing the

button.

Reset to factory settings

Point the ICU at the sensor and press the 

9

 

 

reset button (the sensor blinks green). This sets all 
settings to the default factory settings.

Save setting and exit ICU configuration mode by 
pressing the

button.

Exit without saving by pressing the

button.

Number of flashes

1

2

3

4

5

Range (cm approx)

8

11

14

16

18

Number of flashes

1

2

3

4

5

6

7

8

Run-on time (sec)

1

2

3

4

5 10 20 30

Number of flashes

1

2

3

4

5

6

Hygiene rinse time 
(sec)

0

5

10 15 30 60

Содержание Novatap

















Отзывы: