manualshive.com logo in svg

Cisco Universal Broadband Router Cisco uBR10012, Руководство по настройке программного обеспечения

Универсальный широкополосный маршрутизатор Cisco uBR10012 предлагает множество возможностей для настройки программного обеспечения. Вы можете бесплатно загрузить Руководство по настройке программного обеспечения на manualshive.com. Получите подробное описание продукта и инструкции по использованию, чтобы максимизировать его потенциал.

Поделиться
Скачать
background image

3-26

Cisco uBR10012 Universal Broadband Router Software Configuration Guide

OL-1520-05

Chapter 3      Configuring Cable Interface Features for the Cisco uBR10012 Router

Configuring the Upstream Cable Interface

  •

Upstream rate-shaping option to the 

token-bucket

 keyword

  •

A default state change from 1-second burst policing to token bucket with shaping 

Tip

Upstream grant shaping is per CM (per service ID (SID)). Shaping can be enabled or disabled for the 
token-bucket algorithm.

Note

Before the introduction of this feature, the CMTS would drop bandwidth requests from a CM it 
detected as exceeding its configured peak upstream rate. Such request dropping affects the 
throughput performance of IP-based protocols such as FTP, TCP, and Simple Network Management 
Protocol (SNMP). With this feature, the CMTS can shape (buffer) the grants for a CM that is 
exceeding its upstream rate, rather than dropping the bandwidth requests. 

Router# 

show interface c5/0/0 sid 1 counters

00:02:23: %ENVM-3-LASTENV: Cannot save environmental data 
Sid  Req-polls  BW-reqs    Grants     Packets    Frag       Concatpkts
     issued     received   issued     received   complete   received
1    0          22         22         22         0          0          
2    0          3          3          2          0          0          
3    0          0          0          0          0          0 

Verifying Upstream Traffic Shaping

To determine if upstream traffic shaping is configured and activated, enter the

 show running-config

 

command and look for the cable interface configuration information. If upstream traffic shaping is 
configured and enabled, a traffic shaping entry appears in the 

show running-config 

output. If upstream 

traffic shaping is disabled,

 

no cable upstream rate-limit 

appears in the output.

You can also perform the following tasks to verify that traffic shaping is enabled on the upstream channel:

Step 1

Configure a low-peak upstream rate limit for the CM in its QoS profile. Either use the command-line 
interface (CLI) to modify the modem’s QoS profile, or edit the modem’s TFTP configuration file. refer 
to the 

DOCSIS 1.1 for the Cisco uBR7200 Series Universal Broadband Routers

 feature module at 

http://www.cisco.com/en/US/docs/cable/cmts/feature/DOCSIS11.html

.

Step 2

Use a regular rate-limiting algorithm on the upstream without rate shaping, and note the drops of the 
excess bandwidth requests from this CM when it exceeds its peak upstream rate. 

Use the 

show interface c

x

/

y

 sid counters verbose 

command to see the bandwidth request drops.

 

Verify 

that the upstream rate received by that modem is less than its configured peak rate, due to the timeouts 
and backoffs produced by the drop in bandwidth requests. Enter the 

show interface c

x/y

 service flow qos 

command to see the input rate at CMTS in bps.

Step 3

Enable grant shaping on the upstream channel by using the new 

shaping

 keyword extension to the 

token-bucket algorithm CLI command.

Step 4

Make the CM exceed its peak upstream rate by generating upstream traffic, and note the effect of grant 
buffering (shaping) at the CMTS. If you use CM-to-CMTS pings, there is a perceivable decrease in the 
frequency of the pings. 

Let the pings run long enough to allow the averages at the CMTS to settle; then view the upstream rate 
received by this single modem. Use the 

show interface c

x

/

y

 command and see the input rate in bps. This 

value should be close to the modem’s peak upstream rate. Also note the drop counts for the modem’s 
SID by using the 

show interface sid counters 

command, and verify that the CMTS no longer drops the 

bandwidth requests from the CM.

Содержание Universal Broadband Router Cisco uBR10012

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Universal Broadband Router Cisco uBR10012

ZALMAN CNPS17X User Manual preview
CNPS17X
Бренд: ZALMAN Страницы: 20
B+B SmartWorx UR5i v2 Libratum Start Manual preview
UR5i v2 Libratum
Бренд: B+B SmartWorx Страницы: 8
B+B SmartWorx ICR-1601 Start Manual preview
ICR-1601
Бренд: B+B SmartWorx Страницы: 8
Patton electronics 1090 Service Manual preview
1090
Бренд: Patton electronics Страницы: 8
Zenith Data Systems Z-100 Series Installation Manual preview
Z-100 Series
Бренд: Zenith Data Systems Страницы: 64
H3C CR16006-F Configuration Examples preview
CR16006-F
Бренд: H3C Страницы: 21
Fortinet FortiAP S311C Quick Start Manual preview
FortiAP S311C
Бренд: Fortinet Страницы: 20
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Бренд: ADC Страницы: 7
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
Mercusys MR30G Quick Installation Manual preview
MR30G
Бренд: Mercusys Страницы: 35
bintec elmeg RM7000 Installation Manual preview
RM7000
Бренд: bintec elmeg Страницы: 33
Juniper MX2010 Hardware Manual preview
MX2010
Бренд: Juniper Страницы: 825
OpenVox B800P User Manual preview
B800P
Бренд: OpenVox Страницы: 13
Renesas RL78/G1H User Manual preview
RL78/G1H
Бренд: Renesas Страницы: 941
Eicon Networks Diva 2440 Quick Start Manual preview
Diva 2440
Бренд: Eicon Networks Страницы: 32
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Бренд: Parker Страницы: 107
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Бренд: Moxa Technologies Страницы: 51
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Бренд: ivideon Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды