manualshive.com logo in svg

Cisco UCS B260 M4, Инструкция по установке и обслуживанию

Поделиться
Скачать
Cisco UCS B260 M4 Скачать руководство пользователя страница 18

Figure 5: Removing a Slot Divider

To reinstall the slot divider, align it with the dimples in the slot top and bottom and slide it back
in until it clicks into place.

Tip

Step 2

Grasp the front of the blade module and place your other hand under the blade to support it.

Figure 6: Positioning a UCS B260 M4 Blade Module in the Chassis

Step 3

Open the ejector levers in the front of the blade module.

Step 4

Gently slide the blade into the blade slot opening until you cannot push it any farther.

Step 5

Press the ejector levers so that they latch with the edge of the chassis and press the blade module all the way
in.

Step 6

Tighten the captive screw on the front of the blade to no more than 3 in-lbs. Tightening with bare fingers will
prevent stripped or damaged captive screws.

Step 7

Attach the UCS Scalability Terminator or UCS Scalability Connector to the blade module(s) as follows:

Cisco UCS B260 M4 and B460 M4 Blade Server Installation and Service Note for Servers with E7 v3 and E7 v2 CPUs

10

Installing a Blade Server

Installing a Blade Server in the Chassis

Содержание UCS B260 M4



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды