Cisco SFS 7012 Скачать руководство пользователя страница 71

Страница: 71 / 176

2-29

Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide

OL-8787-05

The configuration files have been successfully backed up for a particular slot.

•

CfgSrvModeDisabled

An event has occurred that has caused the slot mode to be set to disabled. The user should resolve
the error and reset the mode to the proper value for the affected slot.

Note

The default settings for this screen are as shown above. The user should not change the defaults unless
instructed by Technical Support.

Chassis Traps

The Chassis Trap Control screen allows the user to set default trap scenarios related to SFS 7012.

Figure 2-53 Chassis Trap Control

Step 1

Click

Chassis

Step 2

Click

Chassis Traps

Step 3

Click

Trap Control

. The

Chassis Trap Control

screen is displayed.

Figure 2-54 Chassis Trap Control Screen

Step 4

Select or deselect the desired trap(s).

Note

To generate an immediate trap, click the applicable

Gen Trap

button.

Step 5

To save settings, click on

Apply

Following are definitions for each chassis trap:

Chassis Group

icsChassisTrapSystemSelfTestFailure

Содержание SFS 7012

















































































































































































Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды

Cisco SFS 7012, Руководство пользователя по оборудованию

Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды