Cisco SFS 7012 Скачать руководство пользователя страница 39

Страница: 39 / 176

1-29

Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide

OL-8787-05

•

Amber

indicates that the following warning condition exists:

–

A single fan rotation failure at less than 4000 RPM or greater than 10950 RPM.

•

Red

indicates a possible problem, including:

–

The fan tray is not responding to commands for configuration and temperature-related
operations.

–

A fan is not responding to commands for temperature and speed related operations.

–

The fan speed has fallen below the minimum allowed RPM for a fan.

Power Supply LEDs

Each SFS 7012 power supply has two LEDs: DC OK and AC OK. Following are the statuses for each.

DC OK

–

Green

indicates that DC power is normal.

–

Off

indicates a DC power failure or no DC power is present.

AC OK

–

Green

indicates that AC power is normal.

–

Off

indicates a AC power failure or no AC power is present.

SFS 7012 Leaf and Spine Module LEDs

Leaf Module IB Port LEDs

Each SFS 7024 leaf module port has a

Blue

IB link status LED that provide the following indications:

•

- the logical link is up (port is in the Active state).

•

Off

- the physical link is down (port is in the Down state).

Spine and Leaf Module Status LED

The status LED indicates one of the following conditions:

•

Steady

Green

- the module is operating normally.

•

Blinking

Green

- LED test state.

•

Off

- module is in the removable state.

Spine and Leaf Module Attention LED

The Attention LED indicates one of the following conditions:

•

Off

- the system functioning normally.

•

Steady

Amber

- the system requires some attention, which could indicate one of the following

conditions:

–

The switch temperature is at a warning level on the module.

–

The switch silicon temperature is at a warning level (approximately 90 degrees C).

–

DC voltages on the board are slightly out of tolerance (12V Bulk, 5V, 3.3V, 1.8V, VBIO are all
monitored).

Содержание SFS 7012

















































































































































































Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды

Cisco SFS 7012, Руководство пользователя по оборудованию

Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды