Cisco SFS 7012 Скачать руководство пользователя страница 64

Страница: 64 / 176

2-22

Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide

OL-8787-05

Note

The combination of the Transport Domain and the Transport Address determines the trap destination.

•

Port

Specifies the TCP or UDP port that the SNMP trap is sent.

•

Timeout

Specifies the time (in milliseconds) that the trap sender waits on a response before re-sending the trap.

•

Retry Count

Specifies the number of attempts to be made to send the trap after a timeout condition occurs.

Note

Timeout and Retry Count are SNMP v2.c and above. Not applicable for v1 traps.

•

Tag List

Specifies which traps should be sent to a particular destination.

Note

RFC2233 specifies the link up/down traps. Including RFC2233 in the Tag List specifies that the trap
receiver will get link up/down traps.

•

Parameters

Specifies a mapping to an entry in the SNMP Target Parameters table, determining the version of
SNMP to use.

•

Storage Type

This field determines whether or not the entry is saved for each reboot of the SFS 7012.

–

Nonvolatile

means that the value is saved, and remains with each subsequent reboot.

–

Volatile

Other

indicates it will not be saved.

•

Status

Indicates the current status of the row. The row may be in one of three states:

–

Active

–

Not in service

–

Not Ready

Note

A status of

not in service

indicates that the current row will not be used in the event a trap is generated

by the system. Toggling a trap to not in service, which temporarily suspends trap forwarding, may be
useful to keep values intact.

SNMP Target Parameters:

•

Parameter Name

Specifies a mapping to an entry in the SNMP Target Parameters table, determining the version of
SNMP to use.

•

MP Model

Содержание SFS 7012

















































































































































































Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды

Cisco SFS 7012, Руководство пользователя по оборудованию

Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды