Cisco SFS 7012 Скачать руководство пользователя страница 35

Страница: 35 / 176

1-25

Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide

OL-8787-05

Step 13

Enter the new switch default gateway IP address.

Step 14

Click Apply.

Note

A reboot is required to activate the new gateway IP address.

Updating Management Spine IP Addresses in a Redundant Management Configuration

Note

This procedure should be performed the first time the SFS 7012 is powered on.

Each managed spine must have a unique IP address that is different than the chassis IP address of the
SFS 7012. Therefore, a redundantly-managed SFS 7012 will have three (3) unique IP addresses. The
current default IP addresses are:

–

Chassis: 192.168.100.9

–

Spine 1: 192.168.100.11

–

Spine 2: 192.168.100.12

It is necessary for each managed spine to have a unique IP address for the following reasons:

•

Unique IP addresses are used when sending syslog messages from a managed spine to a syslog
server.

•

Gives the user the ability to ping each management spine separately.

•

If the IP addresses are not unique, collisions will occur, causing IP operations to fail.

To update the IP address on a managed spine, do the following:

Step 1

Ensure that the spine module is connected to a COM port on a serial terminal device via the RS-232 port.

Step 2

Get to a

[boot]:

prompt by following Step a or b.

If the managed spine is running, enter the following command at the console:

reboot

Then press

Enter

If the managed spine is not running, power on the switch.

Step 3

After selecting

image1

image2

, press the

Spacebar

to interrupt the auto load sequence before the

counter expires (within 5 seconds).

Step 4

At the

[boot]:

prompt enter the new spine IP address with the following syntax:

spineip <NEW IP ADDRESS>

Then press

Enter

Содержание SFS 7012

















































































































































































Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды

Cisco SFS 7012, Руководство пользователя по оборудованию

Результаты поиска

Содержание SFS 7012

Отзывы:

Похожие инструкции для SFS 7012

Бренды по названию

Популярные бренды