background image

4-16

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 4      Configuring the PA-POS-2OC3

  Checking the Configuration

Using the show diag Command

Display the types of port adapters installed in your system (and specific information about each) using 
the 

show diag

 

slot

 command, where 

slot

 is the 

port adapter slot

 in a Cisco 7200 VXR series router, 

Cisco 7201 router, Cisco 7301 router, and Cisco 7401ASR router, the 

module slot

 in a Cisco 7304 PCI 

Port Adapter Carrier Card in a Cisco 7304 router, and the 

interface processor slot

 in a Cisco 7500 series 

router with a VIP. In the FlexWAN module, the 

show diag

 command is used without the 

slot 

designation. 

Note

The outputs that appear in this document may not match the output you receive when running these 
commands. The outputs in this document are examples only.

The following sections provide platform-specific output examples using the 

show diag

 command:

  •

Cisco 7200VXR Series Routers—Example Output of the show diag Command, page 4-16

  •

Cisco 7201 Router—Example Output of the show diag Command, page 4-17

  •

Cisco 7301 Router—Example Output of the show diag Command, page 4-17

  •

Cisco 7304 Router—Example Output of the show diag Command, page 4-18

  •

Cisco 7401ASR Router—Example Output of the show diag Command, page 4-20

  •

VIP in Cisco 7500 Series Routers—Example Output of the show diag Command, page 4-21

  •

Cisco 7600 Series Routers with FlexWAN and Enhanced FlexWAN—Example Output of the show 
diag Command, page 4-22

Cisco 7200VXR Series Routers—Example Output of the show diag Command

Following is an example of the 

show diag 

command for a PA-POS-2OC3 in port adapter slot 2 of a Cisco 

7200 VXR router:

Router# 

show diag 2

Slot 2:

Dual OC3 POS Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time 16:01:44 ago

EEPROM contents at hardware discovery:

Hardware Revision        :1.0

PCB Serial Number        :00000000000

Part Number              :73-8220-01

Board Revision           :01

RMA Test History         :00

RMA Number               :0-0-0-0

RMA History              :00

Unknown Field (type 0088):00 00 00 00

Product Number           :PA-POS-2OC3

Top Assy. Part Number    :800-21857-01

EEPROM format version 4

EEPROM contents (hex):

0x00:04 FF 40 03 E3 41 01 00 C1 8B 30 30 30 30 30 30

0x10:30 30 30 30 30 82 49 20 1C 01 42 30 31 03 00 81

0x20:00 00 00 00 04 00 88 00 00 00 00 CB 94 50 41 2D

0x30:50 4F 53 2D 32 4F 43 33 20 20 20 20 20 20 20 20

0x40:20 C0 46 03 20 00 55 61 01 FF FF FF FF FF FF FF

0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Содержание PA-POS-2OC3





































































































Отзывы: