Cisco PA-POS-2OC3 Скачать руководство пользователя

Страница: 84 / 100

4-16

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 4 Configuring the PA-POS-2OC3

Checking the Configuration

Using the show diag Command

Display the types of port adapters installed in your system (and specific information about each) using
the

show diag

slot

command, where

slot

is the

port adapter slot

in a Cisco 7200 VXR series router,

Cisco 7201 router, Cisco 7301 router, and Cisco 7401ASR router, the

module slot

in a Cisco 7304 PCI

Port Adapter Carrier Card in a Cisco 7304 router, and the

interface processor slot

in a Cisco 7500 series

router with a VIP. In the FlexWAN module, the

show diag

command is used without the

slot

designation.

Note

The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.

The following sections provide platform-specific output examples using the

show diag

command:

•

Cisco 7200VXR Series Routers—Example Output of the show diag Command, page 4-16

•

Cisco 7201 Router—Example Output of the show diag Command, page 4-17

•

Cisco 7301 Router—Example Output of the show diag Command, page 4-17

•

Cisco 7304 Router—Example Output of the show diag Command, page 4-18

•

Cisco 7401ASR Router—Example Output of the show diag Command, page 4-20

•

VIP in Cisco 7500 Series Routers—Example Output of the show diag Command, page 4-21

•

Cisco 7600 Series Routers with FlexWAN and Enhanced FlexWAN—Example Output of the show
diag Command, page 4-22

Cisco 7200VXR Series Routers—Example Output of the show diag Command

Following is an example of the

show diag

command for a PA-POS-2OC3 in port adapter slot 2 of a Cisco

7200 VXR router:

Router#

show diag 2

Slot 2:

Dual OC3 POS Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time 16:01:44 ago

EEPROM contents at hardware discovery:

Hardware Revision :1.0

PCB Serial Number :00000000000

Part Number :73-8220-01

Board Revision :01

RMA Test History :00

RMA Number :0-0-0-0

RMA History :00

Unknown Field (type 0088):00 00 00 00

Product Number :PA-POS-2OC3

Top Assy. Part Number :800-21857-01

EEPROM format version 4

EEPROM contents (hex):

0x00:04 FF 40 03 E3 41 01 00 C1 8B 30 30 30 30 30 30

0x10:30 30 30 30 30 82 49 20 1C 01 42 30 31 03 00 81

0x20:00 00 00 00 04 00 88 00 00 00 00 CB 94 50 41 2D

0x30:50 4F 53 2D 32 4F 43 33 20 20 20 20 20 20 20 20

0x40:20 C0 46 03 20 00 55 61 01 FF FF FF FF FF FF FF

0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Содержание PA-POS-2OC3





































































































Результаты поиска

Содержание PA-POS-2OC3

Отзывы:

Похожие инструкции для PA-POS-2OC3

Бренды по названию

Популярные бренды

Cisco PA-POS-2OC3, Руководство по установке и настройке

Результаты поиска

Содержание PA-POS-2OC3

Отзывы:

Похожие инструкции для PA-POS-2OC3

Бренды по названию

Популярные бренды