manualshive.com logo in svg

Cisco PA-POS-2OC3, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-POS-2OC3 Скачать руководство пользователя страница 63

3-15

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 3      Removing and Installing Port Adapters

  Connecting PA-POS-2OC3 Interface Cables

Connecting PA-POS-2OC3 Interface Cables

To continue your PA-POS-2OC3 installation, you must connect the interface cables. The instructions 
that follow apply to all supported platforms.

Note

Optical fiber cables are not available from Cisco Systems; they are available from outside commercial 
cable vendors. For more information on the cables you should use with this port adapter, see the 

“Cables 

and Connectors” section on page 1-6

.

To connect cables to the Cisco PA-POS-2OC3, attach either one duplex optical fiber cable or two simplex 
optical fiber cables between the Cisco PA-POS-2OC3 interface port on your PA-POS-2OC3 and your 
network. (See 

Figure 3-6

.) 

Make sure that the receive (RX) cable goes to RX LC-type receptacle and transmit (TX) cable goes to 
TX LC-type receptacle on the PA-POS-2OC3.

Figure 3-6

Connecting Simplex or Duplex Optical Fiber Cables to the Cisco PA-POS-2OC3

Warning

Class 1 laser product. 

Statement 1008

Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into 
beams or view directly with optical instruments. 

Statement 1051

84947

2 simplex

connectors

To external

OC-3 network

To external

OC-3 network

TX

RX

1 duplex

connector

TX RX

or

PA-POS-2OC3

ALARM

RCV

ALARM

ENABLED

RCV

TX

TX

RX

POS 1

RX

POS 0

CLASS 1 LASER PRODUCT

LASERPRODUKT DER KLASSE 1

PRODUIT LASER DE CLASSE 1

PRODUCTO LASER CLASE 1

Содержание PA-POS-2OC3





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды