manualshive.com logo in svg

Cisco PA-POS-2OC3, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-POS-2OC3 Скачать руководство пользователя страница 54

3-6

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 3      Removing and Installing Port Adapters

  Port Adapter Removal and Installation

Cisco 7200 VXR Routers—Removing and Installing a Port Adapter in the Port 
Adapter Jacket Card

The Port Adapter Jacket Card is used in the I/O controller slot of a Cisco 7200 VXR router with an 
NPE-G1 installed, and allows a port adapter to be installed in it. The NPE-G1 incorporates I/O controller 
functionality, so that with either network processing engine the I/O controller slot is available. The 
NPE-G1 has a third dedicated peripheral component interconnect (PCI) bus that provides additional 
bandwidth to the chassis. The third PCI bus allows a port adapter with a high bandwidth point 
requirement to be used with the Port Adapter Jacket Card in the I/O controller slot.

Note

Online insertion and removal (OIR) is not supported on the Port Adapter Jacket Card. OIR is supported 
on the port adapter. You must have the chassis powered off to install or remove the Port Adapter Jacket 
Card.

Figure 3-2

Port Adapter Jacket Card Faceplate

Use the following information to install a port adapter into an installed Port Adapter Jacket Card. For 
information on installing the Port Adapter Jacket Card into a Cisco 7200 VXR router, see the 

Port Adapter  Jacket Card Installation Guide

.

1

Captive installation screw

4

Handle

2

ENABLE LED

5

Port adapter slot

3

PWR (power) LED

Table 3-1

Port Adapter Jacket Card LEDs

LED 

Color

Indicates

ENABLE

Green

Port Adapter Jacket Card is enabled for operation.

Off

Port Adapter Jacket Card is not enabled for operation.

PWR (power)

Green

Port Adapter Jacket Card is receiving power.

Off

Port Adapter Jacket Card is not receiving power.

138883

PORT ADAPTER JACKET CARD

ENABLED

PWR

3

2

4

5

1

4

1

Содержание PA-POS-2OC3





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды