Cisco NC55A2-MOD-SE-H-S Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

Figure 5: Handling a Modular Port Adapter

Metal Carrier

2

Printed Circuit Board

1

Grounding Strap

3

Online Insertion and Removal

Cisco NCS 5500 series modular port adapters (MPAs) support online insertion and removal (OIR).

Modular port adapters (MPAs) support the following types of OIR:

• Soft OIR

Soft OIR uses the IOS XR

hw-module subslot rack/slot/subslot reload

,

hw-module subslot

rack/slot/subslot shutdown

, and

no hw-module subslot rack/slot/subslot shutdown

commands to

complete online insertion and removal.

• Managed OIR

A managed online insertion and removal of Modular port adapters (MPAs) is comprised of the following
steps:

• Shut down the MPA with the

hw-module subslot rack/slot/subslot shutdown

command.

• Confirm that the LEDs have gone from green to off.

• Execute the

do show platform

command to verify that the MPA to be removed is in the disabled

state.

• Physically remove the MPA to be replaced.

• Physically insert the replacement MPA

• Return the MPA to the up state with the

no hw-module subslot rack/slot/subslot shutdown

command.

• Hard OIR

You can perform the OIR in a running system, by not executing any commands:

Connect Router to the Network

8

Connect Router to the Network

Online Insertion and Removal

«
...
6
7
8
9
10
...
»

Содержание NC55A2-MOD-SE-H-S

























Отзывы:

Нет отзывов

Похожие инструкции для NC55A2-MOD-SE-H-S

Бренд: X-Micro Страницы: 74

Бренд: NetComm Страницы: 3

Бренд: Teknim Страницы: 10

Бренд: NETGEAR Страницы: 2

Бренд: Perle Страницы: 2

AyrMesh IndoorAP

Бренд: AYRSTONE Страницы: 2

Бренд: Asante Страницы: 150

Бренд: Lanner Страницы: 38

Бренд: Allied Telesis Страницы: 34

Бренд: Tripp Lite Страницы: 2

Бренд: PairGain Страницы: 80

XC-16CH-NVR-4TB

Бренд: Xyclop Страницы: 19

Бренд: Patton electronics Страницы: 8

Бренд: LevelOne Страницы: 49

Бренд: Maestro Wireless Solution Страницы: 22

Edge-Core A07-ES4548C

Бренд: Atlantis Land Страницы: 2

Бренд: Juniper Страницы: 230

Бренд: Geneko Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды