Cisco NC55A2-MOD-SE-H-S Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

background image

c) Slide the transceiver out of the socket.

Figure 15: Removing the 40-Gigabit QSFP+ or 100-Gigabit QSFP28 Transceiver Module

Step 4

Place the QSFP+ or QSFP28 transceiver module into an antistatic bag.

Installing and Removing CFP2 Modules

Before you remove or install a CFP2 module, read the installation information in this section.

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams
or view directly with optical instruments.

Statement 1051

Warning

The CFP2 module is a static-sensitive device. Always use an ESD wrist strap or similar individual grounding
device when handling the CFP2 modules or coming into contact with the modules.

Caution

Installing a CFP2 Module

To install a CFP2 module, follow these steps:

Step 1

Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.

Step 2

Align the CFP2 module into the transceiver port socket of the line card.

Connect Router to the Network

19

Connect Router to the Network

Installing and Removing CFP2 Modules

«
...
17
18
19
20
21
...
»

Содержание NC55A2-MOD-SE-H-S

























Отзывы:

Нет отзывов

Похожие инструкции для NC55A2-MOD-SE-H-S

Бренд: D-Link Страницы: 13

Бренд: Patton electronics Страницы: 2

NI WLS/ENET-9163

Бренд: National Instruments Страницы: 36

Бренд: 3Com Страницы: 32

Бренд: WAGO Страницы: 2

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Бренд: Planet Страницы: 2

Бренд: Planet Страницы: 13

Бренд: MICRADIGITAL Страницы: 2

IntraSwitch 5324MT

Бренд: Asante Страницы: 2

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: 3Com Страницы: 63

Бренд: Martin Страницы: 41

IE-SW-AL18M-16TX-2GC

Бренд: Weidmüller Страницы: 2

Бренд: NETGEAR Страницы: 3

Бренд: Commax Страницы: 122

Бренд: ADTRAN Страницы: 2

NetVanta 1335 Series

Бренд: ADTRAN Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды