Cisco NC55A2-MOD-SE-H-S Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

background image

Electrical connection to
the module circuitry

3

40GBASE QSFP+
transceiver body

1

Bail-clasp latch

2

Required Tools and Equipment

You need these tools to install the 40-Gigabit QSFP+ / 100-Gigabit QSFP28 transceiver modules:

• Wrist strap or other personal grounding device to prevent ESD occurrences.

• Antistatic mat or antistatic foam to set the transceiver on.

• Fiber-optic end-face cleaning tools and inspection equipment.

For information on inspecting and cleaning fiber-optic connections, see

Maintain Transceivers and Optical

Cables

.

Installing the 40-Gigabit QSFP+ or 100-Gigabit Transceiver Module

The QSFP+ or QSFP28 transceiver module can have either a bail-clasp latch or a pull-tab latch. Installation
procedures for both types of latches are provided.

The QSFP+ or QSFP28 transceiver module is a static-sensitive device. Always use an ESD wrist strap or
similar individual grounding device when handling QSFP+ or QSFP28 transceiver modules or coming into
contact with system modules.

Caution

To install an QSFP+ or QSFP28 transceiver module, follow these steps:

Step 1

Attach an ESD wrist strap to yourself and a properly grounded point on the chassis or the rack.

Step 2

Remove the QSFP+ or QSFP28 transceiver module from its protective packaging.

Step 3

Check the label on the QSFP+ or QSFP28 transceiver module body to verify that you have the correct model for your
network.

Step 4

For optical QSFP+ or QSFP28 transceiver modules, remove the optical bore dust plug and set it aside.

Step 5

For QSFP+ or QSFP28 transceiver modules equipped with a pull-tab, hold the transceiver so that the identifier label is
on the top.

Step 6

For QSFP+ or QSFP28 transceiver modules equipped with a bail-clasp latch, keep the bail-clasp aligned in a vertical
position.

Step 7

Align the QSFP+ or QSFP28 transceiver module in front of the module’s transceiver socket opening and carefully slide
the QSFP+ or QSFP28 transceiver into the socket until the transceiver makes contact with the socket electrical connector
(see the figure below).

Connect Router to the Network

15

Connect Router to the Network

Required Tools and Equipment

«
...
13
14
15
16
17
...
»

Содержание NC55A2-MOD-SE-H-S

























Отзывы:

Нет отзывов

Похожие инструкции для NC55A2-MOD-SE-H-S

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: Funkwerk Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 184

Бренд: H3C Страницы: 12

Бренд: 4G Systems Страницы: 2

Бренд: Unex Страницы: 27

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: KYLAND Technology Страницы: 24

Бренд: Steren Страницы: 130

Бренд: WTI Страницы: 178

Бренд: ACTi Страницы: 12

Бренд: TRENDnet Страницы: 7

Бренд: Patton electronics Страницы: 8

Бренд: Acrosser Technology Страницы: 42

Бренд: D-Link Страницы: 191

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды