Cisco MDS 9120 - Fabric Switch Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 124

background image

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m

1-16

Cisco MDS 9100 Series Hardware Installation Guide

OL-21514-01

Chapter 1 Product Overview

Supported SFP and SFP+ Transceivers

Supported SFP and SFP+ Transceivers

The following types of SFP transceivers are available from Cisco Systems and are supported on the
Cisco MDS 9100 Series:

•

Fibre Channel SFP transceivers, in either short wavelength (SWL) or long wavelength (LWL)

•

Combination Fibre Channel/Gigabit Ethernet SFP transceivers, in either SWL or LWL

•

Combination Fibre Channel/Gigabit Ethernet course wavelength division multiplexers (CWDM)
SFP transceivers, which can be used for extended long wavelength (ELWL) transmission or for
CWDM

•

Combination Fibre Channel/Gigabit Ethernet dense wavelength division multiplexers (DWDM)

Note

Switches running Cisco MDS SAN-OS Release 1.1(1a) or later and MDS NX-OS Release 4.1(1b) or
later support combination Fibre Channel/Gigabit Ethernet SFP transceivers.

SFP transceivers are field-replaceable. You can use any combination of SFP transceivers that are
supported by the switch. The only restrictions are that SWL transceivers must be paired with SWL
transceivers, and LWL transceivers with LWL transceivers, and the cable must not exceed the stipulated
cable length for reliable communications.

SFP tranceivers can also be used in extended distances, but it would depend on the allocation of available
Buffer-To-Buffer (B2B) credits on specific ports in the switch. For more information on Buffer-to-Buffer
(B2B) credits, see the Configuring Interface Buffers chapter in the Cisco MDS 9000 Family NX-OS
Interfaces Configuration Guide.

For the list of supported SFP transceivers, see the Cisco MDS 9000 Family Release Notes for Cisco MDS
NX-OS Releases. For more information about a specific Cisco SFP transceiver, see the

“SFP Transceiver

Specifications” section on page B-6

. SFP transceivers can be ordered separately or with the Cisco MDS

9100 Series.

Port speed

On

2-Gbps mode.

Off

1-Gbps mode.

Port link

Solid green

Link is up.

Steady flashing
green

Link is up (beacon used to identify port).

1

Intermittent
flashing green

Link is up (traffic on port).

Solid orange

Link is disabled by software.

Flashing orange

A fault condition exists.

1.

The flashing green light turns on automatically when an external loopback is detected that causes the interfaces to be isolated.
The flashing green light overrides the beacon mode configuration. The state of the LED is restored to reflect the beacon mode
configuration after the external loopback is removed.

Table 1-3

Switching Module LEDs (continued)

LED

Status

Description

«
...
30
31
32
33
34
...
»

Содержание MDS 9120 - Fabric Switch





























































































































Отзывы:

Нет отзывов

Похожие инструкции для MDS 9120 - Fabric Switch

Бренд: EAW Страницы: 10

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 19

Бренд: National Instruments Страницы: 36

Бренд: National Instruments Страницы: 103

NI PXI-1042 Series

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 4

Бренд: WAGO Страницы: 2

Бренд: D-Link Страницы: 83

Бренд: APM Страницы: 3

Бренд: Patton electronics Страницы: 23

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: Idis Страницы: 31

Бренд: Telex Communications Страницы: 28

Бренд: Teknim Страницы: 10

Бренд: red lion Страницы: 5

18x18 Card Cage

Бренд: WolfPack Страницы: 31

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды