5
IR510 WPAN Gateway and IR530 WPAN Range Extender Hardware Installation Guide
IR510 Installation
WARNING:
When you connect or disconnect the power and/or alarm connector with power applied, an electrical arc can occur. This could
cause an explosion in hazardous area installations. Be sure that all power is removed from the switch and any other circuits. Be sure that
power cannot be accidentally turned on or verify that the area is nonhazardous before proceeding. Statement 1058
WARNING:
In switch installations in a hazardous location, the DC power source could be located away from the vicinity of the switch.
Before performing any of the following procedures, locate the DC circuit to ensure that the power is removed and cannot be turned on
accidentally, or verify that the area is nonhazardous before proceeding. Statement 1059
WARNING:
This equipment is supplied as “open type
”
equipment. It must be mounted within an enclosure that is suitably designed for
those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from
accessibility to live parts. The interior of the enclosure must be accessible only by the use of a tool. The enclosure must meet IP 54 or NEMA
type 4 minimum enclosure rating standards. Statement 1063
WARNING:
Use twisted-pair supply wires suitable for 86°F (30°C) above surrounding ambient temperature outside the enclosure.
Statement 1067
WARNING:
This equipment is intended for use in a Pollution Degree 2 industrial environment, in over-voltage Category II applications (as
defined in IEC publication 60664-1), and at altitudes up to 2000 meters without derating Statement 1068
WARNING:
When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with a proper
wiring method that complies with the governing electrical codes Statement 1069
WARNING:
Do not connect or disconnect cables to the ports while power is applied to the switch or any device on the network because an
electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed from the switch
and cannot be accidentally be turned on, or verify that the area is nonhazardous before proceeding. Statement 1070
WARNING:
Explosion Hazard—Do not connect or disconnect wiring while the field-side power is on; an electrical arc can occur. This could
cause an explosion in hazardous location installations. Be sure that power is removed or that the area is nonhazardous before proceeding.
Statement 1081
WARNING:
Explosion Hazard - The area must be known to be nonhazardous before installing, servicing, or replacing the unit. Statement
1082
WARNING:
Explosion Hazard—Substitution of components may impair suitability for Class I, Division 2/Zone 2. Statement 1083
North American Hazardous Location Approval for WPAN Gateway
Unpacking the IR510
Note:
When you are unpacking the IR510,
do not
remove the foam blocks attached to the antenna connectors. The foam protects the antenna
connectors during installation.
English
Products marked “Class I, Div 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B,
C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on
the rating nameplate indicating the hazardous location temperature code. When combining products within
a system, the most adverse temperature code (lowest “T” number) may be used to help determine the
overall temperature code of the system. Combinations of equipment in your system are subject to
investigation by the local Authority Having Jurisdiction at the time of installation.
French
Informations sur l'utilisation de cet équipement en environnements dangereux:
Les produits marqués "Class I, Div 2, GP A, B, C, D" ne conviennent qu'à une utilisation en
environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit
est livré avec des marquages sur sa plaque d'identification qui indiquent le code de température pour les
environnements dangereux. Lorsque plusieurs produits sont combinés dans un système, le code de
température le plus défavorable (code de température le plus faible) peut être utilisé pour déterminer le
code de température global du système. Les combinaisons d'équipements dans le système sont sujettes à
inspection par les autorités locales qualifiées au moment de l'installation
