Cisco Catalyst 9200CX Compact Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 70

background image

Figure 3: A PCB with Corrosion on its Metal Contacts

EMI and Radio Frequency Interference

Electro-Magnetic interference (EMI) and radio frequency interference (RFI) from a system can adversely
affect devices such as radio and television (TV) receivers operating near the system. Radio frequencies
emanating from a system can also interfere with cordless and low-power telephones. Conversely, RFI from
high-power telephones can cause spurious characters to appear on the system monitor. RFI is defined as any
EMI with a frequency above 10 kilohertz (kHz). This type of interference can travel from the system to other
devices through the power cable and power source, or through the air in the form of transmitted radio waves.
The Federal Communications Commission (FCC) publishes specific regulations to limit the amount of EMI
and RFI emitted by computing equipment. Each system meets these FCC regulations.

When wires are run for any significant distance in an electromagnetic field, interference can occur between
the field and the signals on the wires. This fact has two implications for the construction of plant wiring:

• Bad wiring practice can result in radio interference emanating from the plant wiring.

• Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers

and receivers in the chassis, and even create an electrical hazard by conducting power surges through
lines into equipment.

Cisco Catalyst 9200CX Compact Series Switches Hardware Installation Guide

15

Preparing for Installation

EMI and Radio Frequency Interference

«
...
21
22
23
24
25
...
»

Содержание Catalyst 9200CX Compact Series







































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 9200CX Compact Series

Бренд: Manhattan Страницы: 2

Бренд: Ableconn Страницы: 16

GenReady Series 005448-2

Бренд: Generac Power Systems Страницы: 4

Бренд: KinAn Страницы: 4

Бренд: Eaton Страницы: 2

Бренд: Milestone pro Страницы: 32

Бренд: Lockly Страницы: 12

Бренд: Manhattan Страницы: 4

Бренд: LevelOne Страницы: 76

Бренд: Microsonic Страницы: 2

Бренд: Icy Box Страницы: 12

Бренд: Banner Страницы: 8

ControlZAPP CZ CEFL 10VDC

Бренд: DANLERS Страницы: 2

forerunner series

Бренд: Fore Systems Страницы: 352

EasyZAPP EZ CEFL

Бренд: DANLERS Страницы: 2

Бренд: Xantech Страницы: 5

Бренд: LINK-MI Страницы: 18

Бренд: Field Controls Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды