Cisco Catalyst 4500 Series Скачать руководство пользователя страница 122

Страница: 122 / 194

Chapter 4 Removing and Replacing FRUs

Removing and Replacing the Power Supply

4-8

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Installing an AC-Input Power Supply

Warning

The plug-socket combination must be accessible at all times, because it serves
as the main disconnecting device.

Statement 1019

Follow these steps to install an AC-input power supply:

Step 1

Make sure that the power supply you are installing is not plugged in to a power
outlet and that the power cord is not connected to the power supply.

Step 2

Remove the two Phillips-head screws from the power supply filler plate (if a filler
plate is present).

Step 3

Remove the power supply filler plate (if one is present) and set it aside.

Caution

Use both hands to grasp a power supply.

Step 4

Grasp the power supply handle with one hand. Place your other hand underneath
to support the bottom of the power supply, as shown earlier in

Figure 4-8

Step 5

Slide the power supply all the way into the power supply bay.

Step 6

Using a screwdriver, tighten the two captive installation screws (see

Figure 4-1

)

on the front panel of the AC-input power supply.

Step 7

Make sure the power supply power switch is in the off position (O).

Step 8

Before you connect the power supply to a power source, ensure that all site power
and grounding requirements described in the

Site Preparation and Safety Guide

have been met.

Step 9

Plug the power cord into the power supply (see

Figure 4-9

Содержание Catalyst 4500 Series



































































































































































































Результаты поиска

Содержание Catalyst 4500 Series

Отзывы:

Похожие инструкции для Catalyst 4500 Series

Бренды по названию

Популярные бренды

Cisco Catalyst 4500 Series, Руководство по установке

Результаты поиска

Содержание Catalyst 4500 Series

Отзывы:

Похожие инструкции для Catalyst 4500 Series

Бренды по названию

Популярные бренды