Cisco Catalyst 4500 Series Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 194

background image

Chapter 2 Preparing for Installation

Site Power Requirements and Heat Dissipation

2-4

Catalyst 4500 Series Switches Installation Guide

78-14409-08

•

When removing a component, use any available ejector levers or captive
installation screws to release the bus connectors from the backplane or
midplane.

•

Handle carriers by available handles or edges only; avoid touching the printed
circuit boards or connectors.

•

Place a removed component board-side-up on an antistatic surface or in a
static shielding container. If you plan to return the component to the factory,
immediately place it in a static shielding container.

•

Avoid contact between the printed circuit boards and clothing. The wrist strap
only protects components from ESD voltages on the body; ESD voltages on
clothing can still cause damage.

•

Never attempt to remove the printed circuit board from the metal carrier.

Caution

For safety, periodically check the resistance value of the antistatic strap. The
measurement should be between 1 and 10 megohm (Mohm).

Site Power Requirements and Heat Dissipation

This section provides module power requirements and heat dissipation
specifications for the Catalyst 4500 series switches. You should verify site power
before you install the switch.

For more information about power management and planning, refer to the
“Environmental Monitoring and Power Management” chapter in the

Catalyst

4500 Series Switch Cisco IOS Software Configuration Guide

version appropriate

for your software.

Knowing the power requirements is useful for planning the power distribution
system needed to support the switches. You should consider the heat dissipation
specifications when estimating the air-conditioning requirements for an
installation. For all Catalyst 4500 series switches, supervisor engines, and
switching modules in AC or DC environments see the

Catalyst 4500 Series

Module Installation Guide

at

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/module/g
uide/0aspecs.html#wp1012188

«
...
72
73
74
75
76
...
»

Содержание Catalyst 4500 Series



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 4500 Series

Бренд: H3C Страницы: 34

Бренд: Eaton Страницы: 10

Power Xpert Meter 2000

Бренд: Eaton Страницы: 16

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 84

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

FrameSaver 9120

Бренд: Paradyne Страницы: 2

Бренд: AMX Страницы: 1

Бренд: IBM Страницы: 130

Бренд: Planet Страницы: 2

VAR-SOM-MX8M-PLUS

Бренд: Variscite Страницы: 2

Бренд: Sharedband Страницы: 3

Бренд: netsys Страницы: 38

Westermo Ibex-RT-330-5G Series

Бренд: IBEX Страницы: 36

Бренд: Epson Страницы: 24

Бренд: CommScope Страницы: 30

Бренд: Allied Telesis Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды