Cisco Catalyst 4500 Series Скачать руководство пользователя страница 124

Страница: 124 / 194

Chapter 4 Removing and Replacing FRUs

Removing and Replacing the Power Supply

4-10

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Step 12

Verify power supply operation by checking the power supply’s front-panel LEDs.
You should see the following:

•

The LED labeled GOOD is green.

•

The LED labeled FAIL is not lit.

•

The LED labeled FAN OK is green.

Step 13

Check the power supply and system status from the system console by entering
the

show system

command (Catalyst Operating System) or the

show power

command (Cisco IOS). For more information on this command, refer to the
command reference publication for your switch.

Step 14

If the LEDs or the

show system

command (Catalyst Operating System) or the

show power

command (Cisco IOS) output indicate a power problem or other

system problem, see

Chapter 5, “Troubleshooting,”

for more information.

Содержание Catalyst 4500 Series



































































































































































































Результаты поиска

Содержание Catalyst 4500 Series

Отзывы:

Похожие инструкции для Catalyst 4500 Series

Бренды по названию

Популярные бренды

Cisco Catalyst 4500 Series, Руководство по установке

Результаты поиска

Содержание Catalyst 4500 Series

Отзывы:

Похожие инструкции для Catalyst 4500 Series

Бренды по названию

Популярные бренды