Cisco Catalyst 4500 Series Скачать руководство пользователя страница 154

Страница: 154 / 194

Chapter 5 Troubleshooting

Troubleshooting Switching Modules

5-10

Catalyst 4500 Series Switches Installation Guide

78-14409-08

•

The switch powers down and stays down for a few minutes to a few days for
no clear reason.

•

The output-fail LED on the power supplies are red and no power is delivered
to the chassis. The other LEDs on the power supply are green.

•

The Status LEDs on the switching modules and the supervisor engine are
flashing green.

•

CPU Utilization LEDs are flashing green or off.

If you observe these conditions, contact the Cisco TAC for assistance in ordering
replacement redundancy modules and a clock.

Troubleshooting Switching Modules

Each switching module has one LED labeled STATUS that provides information
about the module and one numbered LED labeled LINK for each port on the
module.

Figure 5-1

shows the Gigabit Ethernet port and status LEDs.

Figure 5-2

shows the 10/100BASE-T port LEDs.

Table 5-1

describes the switching module

LEDs and their expected behavior.

Figure 5-1

Gigabit Ethernet Port and Status LEDs

26854

1000BASE-X SWITCHING MODULE

STATUS

WS-X4306-GB GIGABIT ETHERNET

Содержание Catalyst 4500 Series



































































































































































































Результаты поиска

Содержание Catalyst 4500 Series

Отзывы:

Похожие инструкции для Catalyst 4500 Series

Бренды по названию

Популярные бренды

Cisco Catalyst 4500 Series, Руководство по установке

Результаты поиска

Содержание Catalyst 4500 Series

Отзывы:

Похожие инструкции для Catalyst 4500 Series

Бренды по названию

Популярные бренды