Cisco Catalyst 4500 E Series Supervisor Engine 9-E Скачать руководство пользователя страница 17

Страница: 17 / 21

Supported Transceiver Media

For supported transceiver media types, refer to these documents on Cisco.com:

•

Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix

•

Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix

•

Cisco 40-Gigabit Ethernet Transceiver Modules Compatibility Matrix

Transceiver Cabling and Installation

Each port must match the wave-length specifications on the other end of the cable, and the cable must not exceed the stipulated cable
length. For cabling specifications and installation information, refer to these documents on Cisco.com:

•

Cisco SFP and SFP+ Transceiver Module Installation Notes

•

Cisco 40-Gigabit QSFP+ Transceiver Modules Installation Note

Related Reference Installation Information

•

Cisco Mode-Conditioning Patch Cord Installation Note

•

Inspection and Cleaning Procedures for Fiber-Optic Connections

Configuring Your Supervisor Engine

For information about commands that you can use to configure your supervisor engine, refer to the software configuration guide for
your switch under:

Cisco Catalyst 4500 Series Switches Configuration Guides

Related Documentation

For related installation and configuration information, refer to the following:

•

Catalyst 4500 E-Series Switches Installation Guide

•

Catalyst 4500 Series Module Installation Guide

•

Regulatory Compliance and Safety Information for the Catalyst 4500 Series Switches

•

Software Configuration Guides

•

Command Reference Guides

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly

What's New in Cisco Product Documentation

, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html

Содержание Catalyst 4500 E Series Supervisor Engine 9-E





















Результаты поиска

Содержание Catalyst 4500 E Series Supervisor Engine 9-E

Отзывы:

Похожие инструкции для Catalyst 4500 E Series Supervisor Engine 9-E

Бренды по названию

Популярные бренды

Cisco Catalyst 4500 E Series Supervisor Engine 9-E, Инструкция по установке и настройке

Результаты поиска

Содержание Catalyst 4500 E Series Supervisor Engine 9-E

Отзывы:

Похожие инструкции для Catalyst 4500 E Series Supervisor Engine 9-E

Бренды по названию

Популярные бренды