Cisco C9124AXD Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 118

background image

Supplied in the
Kit?

Materials Needed

No

10–mm box-end wrench

No

Outdoor rated shielded ethernet cable

Yes

Ground lug (provided with the access point)

No

Ground block and rod

No

Crimping tool for ground lug, Panduit CT-720 with CD-720-1 die

No

#6 AWG ground wire

Procedure

Step 1

Select a mounting location on the pole to mount the AP. You can attach the AP to a pole having a diameter
of 2 to 5 inch (51 to 127 mm).

Step 2

Hold the bracket up against the pole and slide the three-band straps through the top, middle, and bottom sets
of mounting slots on the mounting bracket.

Step 3

Wrap the band straps around the pole, lock them, and then lightly tighten the clamps using a wrench. Only
tighten them enough to keep the bracket from sliding down the pole

Step 4

Screw an M6 bolt into each of the four bolt holes on the backside of the AP. Do not screw the bolt in all the
way. Leave a gap of about 0.13 inch (3.3 mm).

Step 5

Position the four bolts on the AP into the bracket keyhole slots. Ensure that the AP is seated correctly in the
slots.

The AP should be mounted with the status LED on the base facing downwards.

Note

Step 6

Using a 10–mm wrench, tighten the four bolts that connect the AP to the bracket to 40 lbf-in (4.5 Nm) of
torque.

Step 7

Mount the power supply to the bracket with four #8-32 screws.

Step 8

Locate the AP to its final position. Tighten the band clamps with the wrench. Ensure that the clamps are tight
enough not to let the AP move.

Step 9

Proceed to

Grounding the Access Point, on page 66

Articulating Mount for the AP to a Wall or Ceiling

The optional pivoting mounting kit AIR-MNT-ART1= contains a pivoting mounting bracket for both wall
and pole mounting. This kit allows for adjusting the position of the AP by pivoting the AP along its vertical
plane.

You can also, using this kit, mount the AP to a ceiling in a horizontal plane.

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

48

Installation Overview

Articulating Mount for the AP to a Wall or Ceiling

«
...
54
55
56
57
58
...
»

Содержание C9124AXD























































































































Отзывы:

Нет отзывов

Похожие инструкции для C9124AXD

Бренд: P-Com Страницы: 54

Бренд: Caimore Страницы: 83

Barricade SMCWBR14S-N3

Бренд: SMC Networks Страницы: 106

WAP54GP - Wireless-G Access Point

Бренд: Linksys Страницы: 67

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 111

ROG STRIX GS-AX3000

Бренд: Asus Страницы: 4

Бренд: Asus Страницы: 30

OPTUS DSL-AX5400

Бренд: Asus Страницы: 8

Бренд: Asus Страницы: 52

Бренд: Asus Страницы: 32

Lyra Trio MAP-AC1750

Бренд: Asus Страницы: 56

Бренд: Asus Страницы: 66

Бренд: Asus Страницы: 126

RT-AC1900 Dual Band

Бренд: Asus Страницы: 129

Бренд: Asus Страницы: 143

DSL-N16U Series

Бренд: Asus Страницы: 149

Бренд: Asus Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды