Cisco C9124AXD Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 118

background image

Large Cable Rubber Gland 0.30 to 0.50 inch (7.6
to 12.7 mm) diameter

6

Duplex LC Fiber-optic cable

2

Small Cable Rubber Gland 0.24 to 0.30 inch (6.0
to 7.6 mm) diameter

7

SFP Gland Adapter body

3

Gland nut

8

Body O-ring

4

Step 5

Terminate the SC or LC fiber optic cable.

Figure 85: SC Fiber-optic cable

Optic fiber cable

2

SC optic fiber connector

1

Figure 86: Duplex LC Fiber Optic Cable

Optic fiber cable

2

Duplex LC optic fiber connector

1

Step 6

Using caution not to damage the fiber connector end, pass the fiber connector through the adapter gland
components. Ensure components are ordered and orientated, as shown in

Figure 86: Duplex LC Fiber Optic

Cable, on page 78

Ensure you use the proper rubber gland combination. If the fiber cable outside diameter (OD) is
0.30 to 0.50 inches (7.6 to 12.7 mm), then the small rubber gland can be discarded. If the cable OD
is 0.24 to 0.30 inches (6.0 to 7.6 mm), then the small rubber gland is inserted into the large rubber
gland.

Note

Step 7

Verify the O-ring is correctly seated on the gland adapter body. Re-assemble the components of the adapter
gland. Do not tighten the gland nut on the rubber inserts. Leave it loose so the gland can easily slide on the
fiber cable. If you tightened the cable in this step, you might damage the cable.

Step 8

Insert the SC or LC optic fiber connector-end of the cable into the SFP transceiver module and ensure it latches
into place.

Step 9

Thread the adapter body into the SFP port on the AP. Tighten the adapter body by hand until it is fully seated.
Inspect that the body is seated correctly. Using an adjustable wrench, tighten the body snugly to the AP body
to approximately 13 to 17 lb-in (15 to 20 kgf-cm) of torque.

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

78

Installation Overview

Connecting a Fiber-optic Cable to the AP (AIR-SFP-KIT1=)

«
...
84
85
86
87
88
...
»

Содержание C9124AXD























































































































Отзывы:

Нет отзывов

Похожие инструкции для C9124AXD

Бренд: Ubiquiti Страницы: 36

Бренд: OBERON Страницы: 2

Бренд: Conceptronic Страницы: 121

Бренд: TRENDnet Страницы: 2

Rocket Prism AC GEN 2 RP-5AC-Gen2

Бренд: Ubiquiti Страницы: 28

Бренд: EnGenius Страницы: 5

Бренд: LTE Страницы: 8

Бренд: NC-link Страницы: 26

Magic Box TREBL

Бренд: Sprint Страницы: 33

Бренд: OBERON Страницы: 2

Бренд: Edimax Страницы: 16

Бренд: TP-Link Страницы: 86

Бренд: Linksys Страницы: 125

Бренд: Linksys Страницы: 123

Бренд: wikango Страницы: 20

Бренд: Seltron Страницы: 20

Бренд: EnGenius Страницы: 6

Бренд: EnGenius Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды