background image

 

 

 

 

BROADSOFT PARTNER CONFIGURATION GUIDE – SPECTRALINK 84XX SERIES 

20-BD5605-00 

©

2018 BROADSOFT INC. 

PAGE 19 OF 34 

4.2.1.1  Configure IPV6 Settings 

Spectralink 84xx Series currently does not support IPv6. 

4.2.2  Configure SIP Interface Settings 

Step 

Command 

Description 

System configuration file site.cfg 

Step 1 

Configure the FQDN of the SIP Proxy: 
Example: 

reg.1.server.1.address="as.iop

1.broadworks.net"   
Alternatively, you may use: 
voIpProt.server.1.address=”as.

iop1.broadworks.net”

 

Set the SIP server to the Fully Qualified 

Domain Name (FQDN) of the 

BroadWorks Application Server cluster. 

This FQDN must match the domain 

configured for the BroadWorks 

subscriber’s line/port domain. 
The reg.x parameter is preferred for 

single registrations per phone and may 

be duplicated such that 

reg.2.server.1.address could be used for 

the second registration and so on.  

However, the voIpProt parameter can be 

used to cover all registrations on the 

phone. 

Step 2 

Configure the SIP re-registration interval. 

Example: 
reg.1.server.1.expires=”3600” 
Alternatively, you may use: 
voIpProt.server.1.expires=”360

0”

 

The phone’s requested registration 

period in seconds. 
The reg.x parameter is preferred for 

single registrations per phone and may 

be duplicated such that 

reg.2.server.1.expires could be used for 

the second registration and so on.  

However, the voIpProt parameter can be 

used to cover all registrations on the 

phone. 

Step 3 

Configure the Spectralink 84xx to support 

the Diversion header. 

Example: 
voIpProt.SIP.header.diversion.

enable=”1” 

BroadWorks supports sending/receiving 

redirected call information by use of the 

diversion header. 
If voIpProt.SIP.header.diversion.enable 

is set to 1, the diversion header is 

displayed if received. 

Step 4 

(Optional) Configure an Outbound Proxy 

if a SBC is deployed between the 

Spectralink 84xx and BroadWorks. 

Example: 
voIpProt.SIP.outboundProxy.add

ress=” 
sbc1.iop1.broadworks.net”

 

Set the Outbound Proxy to the Session 

Border Controller (SBC) if one is 

deployed between the Spectralink 84xx 

and BroadWorks. 
If there are redundant SBCs, set it to the 

FQDN for the SBC cluster. 

Step 5 

(Optional) Configure Outbound Proxy 

Failover Behavior when redundant 

proxies are available. 

Example: 
voIpProt.SIP.outboundProxy.fai

lover.onlySignalWithRegistered

=”0” 
voIpProt.SIP.outboundProxy.fai

lover.failback.mode=”newReques

ts” 
voIpProt.SIP.outboundProxy.fai

lover.reRegisterOn=”0”

 

These parameters configure failover 

behavior related to the Outbound proxy. 

Содержание BroadSoft BroadWorks Spectralink 84 Series



































Отзывы: