Cisco ASR 920-24SZ-IM Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 54

background image

Figure 27: Removing the AC Power Supply

Do not use the captive installation screw or the power retainer to pull out the power supply.

Caution

Step 4

Grasp the AC power supply metal tab with one hand, and slide it part of the way out of the chassis. Place your
other hand underneath the power supply, and slide it completely out of the chassis. See

Installing the AC

Power Supply

figure.

Step 5

Replace the AC power supply within 5 minutes. See

Installing the AC Power Supply

figure. If the power

supply bay is to remain empty, install a blank filler plate (Cisco part number 800-39165-01) over the opening,
and secure it with captive installation screws.

Installing and Removing SFP Modules

These sections describe how to install and remove SFP modules. The modules are inserted into the SFP module
slots as depicted in

Installing an SFP Module without a Bale-Clasp Latch into an SFP Module Slot on Cisco

ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router

figure. These field-replaceable modules

provide interfaces.

See the

Supported PIDs

section for the list of SFP modules that the router supports. Each port must match

the wavelength specifications on the other end of the cable. For reliable communications, the cable must not
exceed the stipulated cable length.

Use only Cisco SFP modules on the Cisco router. Each SFP module has an internal serial EEPROM that is
encoded with security information. This encoding provides a way for Cisco to identify and validate that the
SFP module meets the requirements for the router.

For detailed instructions on installing, removing, and cabling the SFP module, see the SFP module
documentation.

Installing the Router

34

Installing the Router

Installing and Removing SFP Modules

«
...
32
33
34
35
36
...
»

Содержание ASR 920-24SZ-IM























































Отзывы:

Нет отзывов

Похожие инструкции для ASR 920-24SZ-IM

Бренд: TDC Страницы: 27

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: Ubiquiti Страницы: 50

Бренд: Paradyne Страницы: 85

Бренд: Patton electronics Страницы: 12

Бренд: Tbus Страницы: 25

Бренд: Faderfox Страницы: 10

Бренд: NC-link Страницы: 20

Бренд: ZKTeco Страницы: 68

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

ISDN SOHO Router

Бренд: AOpen Страницы: 89

Бренд: PairGain Страницы: 80

Бренд: ADDON Страницы: 4

MP5S Plus Writer

Бренд: SONIX Страницы: 23

Бренд: Edge-Core Страницы: 64

Бренд: VERTO Страницы: 48

Barricade SMC7908VoWBRA2

Бренд: SMC Networks Страницы: 2

Westermo Ibex-RT-330-5G Series

Бренд: IBEX Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды