Cisco ASR 920-24SZ-IM Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 54

background image

To disconnect the Linux USB console from the terminal window, enter Ctrl-a followed by : then quit

Installing the Cisco USB Device Driver

A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the USB
serial port on the router.

This procedure describes how to install the Microsoft Windows USB device driver in Microsoft Windows
XP / Windows Vista / Windows 2000 / Windows 7 / Windows 8. Download the driver for your router model
from the Tools and Resources Download Software site,

USB Console Software

category.

To Download the driver, you must have a valid service contract associated to your Cisco.com profile.

Note

Procedure

Step 1

Unzip the file asr-9xx_usbconsole_drivers.zip.

Step 2

Double-click xrusbser_ver2100_installer.exe in the XR21x141x-Win-DriversOnly-Vers2.1.0.0/EXE folder.
Installation Wizard GUI is displayed.

Step 3

Click Next. The InstallShield Wizard Completed window is displayed.

Step 4

Click Finish.

Step 5

Connect the USB cable to the PC and router USB console ports. Follow the on-screen instructions to complete
the installation of the driver.

Step 6

XR21V1401 USB UART Device driver successfully installed message is displayed.

The USB console is ready for use.

Uninstalling the Cisco USB Device Driver

This procedure describes how to uninstall the Microsoft Windows USB device driver in Microsoft Windows
XP / Windows Vista / Windows 2000 / Windows 7 / Windows 8.

Disconnect the router console terminal before uninstalling the driver.

Note

Procedure

Step 1

Choose Start > Control Panel > Add or Remove Programs (Uninstall a program).

Step 2

Scroll to Windows Driver Package - Exar corporation (xrusbser) Ports and click Remove. The Program
Maintenance window is displayed.

Installing the Router

47

Installing the Router

Installing the Cisco USB Device Driver

«
...
45
46
47
48
49
...
»

Содержание ASR 920-24SZ-IM























































Отзывы:

Нет отзывов

Похожие инструкции для ASR 920-24SZ-IM

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

Бренд: Toto Link Страницы: 55

Бренд: H3C Страницы: 4

Бренд: US Robotics Страницы: 180

Бренд: ADTRAN Страницы: 4

OmniStor 4900F Series

Бренд: Rackable Systems Страницы: 196

LinkStation 500

Бренд: Buffalo Страницы: 139

Бренд: Xinje Страницы: 76

Бренд: Juniper Страницы: 6

Бренд: Comelit Страницы: 140

TigerSwitch 100 SMC6924VF

Бренд: SMC Networks Страницы: 174

SteelCentral NetExpress 470

Бренд: Riverbed Страницы: 140

Бренд: Netopia Страницы: 138

Бренд: Westermo Страницы: 22

Бренд: R.V.R. Elettronica Страницы: 171

Passport 8608GTE

Бренд: Nortel Страницы: 10

Бренд: TP-Link Страницы: 25

Y.FORCE YTPC400

Бренд: YTTEK Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды