Cisco ASR 920-24SZ-IM Скачать руководство пользователя страница 8

Страница: 8 / 54

Step 3

Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended
maximum torque is 10 in.-lb.

Step 4

Repeat Step 3 for the other bracket.

Installing the Router Chassis in the Rack

Ensure adequate air flow when mounting the router in a rack. For more information, see the

Air Flow Guidelines

section.

Note

Install the cable guides before installing the router in a 19-inch EIA rack. See

Attaching the Cable Guides

section.

Note

To install the router chassis in the equipment rack, perform these steps:

Procedure

Step 1

Position the chassis in the rack as follows:

• If the front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between

the mounting posts.

• If the rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting

posts.

Installing the Router

Installing the Router Chassis in the Rack

Содержание ASR 920-24SZ-IM























































Результаты поиска

Содержание ASR 920-24SZ-IM

Отзывы:

Похожие инструкции для ASR 920-24SZ-IM

Бренды по названию

Популярные бренды

Cisco ASR 920-24SZ-IM, Установка

Результаты поиска

Содержание ASR 920-24SZ-IM

Отзывы:

Похожие инструкции для ASR 920-24SZ-IM

Бренды по названию

Популярные бренды