Cisco 9300-EX Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 74

background image

Statement 1030

—

Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Installation Options with Racks and Cabinets

You can install the switch in the following types of racks using the rack-mount kit shipped with the switch:

•

Open EIA rack

•

Perforated EIA cabinet

The rack or cabinet that you use must meet the requirements listed in

General Requirements for Cabinets and

Racks, on page 43

.

The rack-mount kit enables you to install the switch into racks of varying depths. You can use the rack-mount
kit parts to position the switch with easy access to either the port connections end of the chassis or the end of
the chassis with the fan and power supply modules. For instructions on how to install the rack-mount kit, see
the

Installing the Switch, on page 16

.

Airflow Considerations

The switch comes with fan and power supply modules that have either port-side intake or port-side exhaust
airflow for cooling the switch. If you are positioning the port end of the switch in a cold aisle, make sure that
the switch has port-side intake fan modules with burgundy coloring. If you are positioning the fan and power
supply modules in a cold aisle, make sure that the switch has port-side exhaust fan modules with blue colorings.
All fan modules must have the same direction of airflow.

Installation Guidelines

When installing the switch, follow these guidelines:

•

Record equipment and installation information in the forms presented in

Chassis and Module Information

as you install and configure the switch.

•

Ensure that there is adequate clearance space around the switch to allow for servicing the switch and
for adequate airflow.

•

Ensure that you are positioning the switch in a rack so that it takes in cold air from the cold aisle and
exhausts air to the hot aisle. If there is blue coloring on the fan modules, the switch is configured for
port-side exhaust airflow and you must position the module side of the switch in a cold aisle. If there is
burgundy coloring on the fan modules, the switch is configured for port-side intake airflow and you
must position the port side of the switch in a cold aisle.

•

Ensure that the chassis can be adequately grounded. If the switch is not mounted in a grounded rack,
we recommend connecting both the system ground on the chassis directly to an earth ground.

•

Ensure that the site power meets the power requirements for the switch. If available, you can use an
uninterruptible power supply (UPS) to protect against power failures.

Cisco Nexus 93180YC-EX ACI Mode Hardware Installation Guide

14

Installing the Switch Chassis

Installation Options with Racks and Cabinets

«
...
22
23
24
25
26
...
»

Содержание 9300-EX











































































Отзывы:

Нет отзывов

Похожие инструкции для 9300-EX

Бренд: KELCO Страницы: 22

Бренд: H3C Страницы: 90

TECMA Silence Marine

Бренд: Thetford Marine Страницы: 9

Бренд: Sangamo Страницы: 2

Бренд: Jerguson Страницы: 4

Personal MiniHub

Бренд: Black Box Страницы: 22

Бренд: PIKA Страницы: 7

Smatrix Wave Plus Uahome Module R-167

Бренд: Uponor Страницы: 48

Бренд: Stahl Страницы: 28

Бренд: Alloy Страницы: 13

Бренд: GoMax Electronics Страницы: 6

ICS5400PTP-12GT12GS4XS

Бренд: 3onedata Страницы: 3

Бренд: NETGEAR Страницы: 2

Sun Datacenter InfiniBand Switch 648

Бренд: Oracle Страницы: 140

Бренд: I-Rocks Страницы: 23

Бренд: Asco Страницы: 36

P.O.P Locks Flex Switch RS1

Бренд: HDC Страницы: 2

Бренд: Ringdale Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды