Cisco 7401ASR Скачать руководство пользователя страница 108

Страница: 108 / 155

A-2

Cisco 7401ASR Installation and Configuration Guide

OL-5419-01 B0

Appendix A Specifications

Software Requirements

The minimum software requirements for the Cisco 7401ASR router are:

•

Cisco IOS Release 12.2 DX

•

Cisco IOS Release 12.2(1)DD

•

Cisco IOS Release 12.2(4)B

•

Cisco IOS Release 12.2(9)YE

•

To check the minimum software requirments of Cisco IOS software with the hardware installed on
your router, Cisco maintains the

Software Advisor

tool on Cisco.com. This tool does not verify

whether modules within a system are compatible, but it does provide the minimum IOS requirements
for individual hardware modules or components.

Note

Access to this tool is limited to users with Cisco.com login accounts.

AC-input cable

18 AWG

three-wire cable, with a three-lead IEC-320 receptacle on the

power supply end, and a country-dependent plug on the power source end

DC Power Supply Information

DC-input power

75W maximum configuration

24V DC-input voltage
ratings

+24 VDC nominal. Maximum range +20 to +36 VDC

24V DC-input current
ratings

Rated for 5A. 3.0A at +24 VDC, 3.75A at +20 VDC (50VA/28 VDC =
1.8A typical draw)

24V DC-input cable

18 AWG recommended minimum, with at least 2 conductors rated for at
least 140

F (60

48V Single and Dual DC Power Supply Information

48V DC-input voltage
rating

–48 VDC

nominal in North America, –60 VDC nominal in some areas of

the European Community. Maximum range is –40.5 to 72 VDC (75 VDC
for 5 mA).

48V DC-input current
rating

Rated for 3A. Not to exceed 1.6A max. at –48 VDC. Not to exceed 2.0A
max. at –40.5 VDC (50VA/–54 VDC = 1.0A typical draw)

48V DC-input cable

18 AWG stranded recommended minimum, rated for at least 140

F (60

Temperature

32 to 104

F (0 to 40

C) operating; –4 to 149

F (–20 to 65

C) nonoperating

Humidity

10% to 90% noncondensing

Mbps = megabits per second

BTU = British thermal units

VAC = volts alternating current

A = amperes

Hz = hertz

AWG = American Wire Gauge

VDC = volts direct current

Table A-1

Cisco 7401ASR System Specifications (continued)

Description

Specification

Содержание 7401ASR




























































































































































Результаты поиска

Содержание 7401ASR

Отзывы:

Бренды по названию

Популярные бренды

Cisco 7401ASR, Руководство по установке и настройке

Результаты поиска

Содержание 7401ASR

Отзывы:

Бренды по названию

Популярные бренды