Cisco 675 - 675 Router Скачать руководство пользователя страница 72

Страница: 72 / 192

Chapter 3

Configuration Procedures for the Cisco 627

Evaluate System Activity and Performance

3-20

Cisco 600 Series Installation and Operation Guide

78-11190-01

Evaluate System Activity and Performance

Table 3-2 describes the LEDs and their status.

Retrieve Statistics

The

stats

command shows information about the number of packets transmitted

and received and activity information about general applications.

Table 3-2

Status LEDs

LED Label

Full Name

Description

WAN-LNK

WAN Link

When this light is ON, it indicates that a link has been
established on the WAN port. The WAN-LNK light blinks
steadily during ADSL line training activities. When the light
is solid, the system is connected and trained.

WAN-ACT

WAN Activity

When this light blinks, it indicates that the WAN port is
transmitting or receiving data.

LAN-LNK

ATM25 LAN Link

When this light is ON, it indicates that a link has been
established on the ATM-25 port.

Note

For some ATM-25 routers or NICs, this light may not
be on till data is sent to the modem.

LAN-ACT

ATM25 LAN Activity When this light blinks, it indicates activity on the ATM-25

port.

PWR

Power Light

When this light is Green, the system is ON and working
correctly.

ALARM

Alarm Light

When the light is Red, the system is ON but indicates a
problem that needs to be resolved.

Содержание 675 - 675 Router

































































































































































































Результаты поиска

Содержание 675 - 675 Router

Отзывы:

Похожие инструкции для 675 - 675 Router

Бренды по названию

Популярные бренды

Cisco 675 - 675 Router, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 675 - 675 Router

Отзывы:

Похожие инструкции для 675 - 675 Router

Бренды по названию

Популярные бренды