manualshive.com logo in svg

Cisco 10008, Руководство по установке и настройке, Страница: 54 / 70

Поделиться
Скачать
Cisco 10008 Скачать руководство пользователя страница 54

54

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

  show pxf cpu access-lists

This section of the sample command output indicates the memory usage of the MiniACLs in the router. 
All of the rows state about the same thing. To determine the actual number of MiniACLs in play, divide 
the memory used in any of blocks 1 to 10 by 256, or blocks 11 to 14 by 16. 

MiniACL XCM Tables:

Block   Use               Memory Used   %Free

  0   IP Src 1 

768    

99

  1   IP Src 2 

768    

99

  2   IP Src 3 

768    

99

  3   IP Src 4 

768    

99

  4   IP Dest 1

768    

99

  5   IP Dest 2

768    

99

  6   IP Dest 3

768    

99

  7   IP Dest 4

768    

99

  8   ToS 

768    

99

  9   Protocol 

768    

99

  10  TCP Flags/Fragment

768    

99

  11  Source Port 1 

48    

99

  12  Source Port 2 

48    

99

  13  Destination Port 2 

48    

99

  14  Destination Port 2 

48    

99

The following describes the information displayed in the last section of the sample output from the 

show 

pxf cpu access-lists security

 command:

Available MiniACL count = 8191

Usable ranges(inclusive):

1->8191

Table 10, Part 4

 describes the significant fields shown in the display.

PRE2 and PRE3 Security ACLs Examples (Cisco 10000 Series Router)

This section compares the output from the 

show pxf cpu access-lists security

 command when issued on 

the PRE2 and PRE3. 

For the PRE2, the following sample output displays VMR (value, plus a mask and result) data for the 
ACL named ICMP_IGMP_MATCH:

Router# 

show pxf cpu access-lists security tcam ICMP_IGMP_MATCH detail

 

-------------------------------------------------------------

VMR Format - handle: 524607B4

Format has 5 fields, refcount = 1

Field: Format, FIXED, start_bit = 69, end_bit = 71

Field: ACL index, FIXED, start_bit = 54, end_bit = 68

Field: Flags, FIXED, start_bit = 43, end_bit = 53

Field: L4 proto, FIXED CNV, start_bit = 16, end_bit = 23

Field: L4 source port, FIXED CNV, start_bit = 0, end_bit = 15 Total bits = 53, format = 72 

GMR used: 5 Col 2 LKBP Vector: 544

-------------------------------------------------------------

VMRs

------ VMR 0 ------

Table 10, Part 4

show pxf cpu access-lists security Field Descriptions 

Field Description

Available MiniACL

The number of ACLs currently available for allocation in 
XCM. 

Usable ranges

The ACL indexes that will be assigned to MiniACLs.

Содержание 10008







































































Отзывы:

Нет отзывов