manualshive.com logo in svg

Cisco 10008, Руководство по установке и настройке, Страница: 38 / 70

Поделиться
Скачать
Cisco 10008 Скачать руководство пользователя страница 38

38

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

  Analyzing and Troubleshooting Packets

Displaying OBFL Data

The 

show logging onboard [status] <module> <slotnumber/subslotnumber/modulenumber>

 

command displays the logs from the OBFL data. On the Cisco 10000 series router the term module is 
used to represent a Route Processor (RP) or the SPA Interface Processor (SIP).

For information on OBFL commands, see the “Configuration Tasks” chapter in the 

Onboard Failure 

Logging

 feature guide located at the following URL:

http://www.cisco.com/en/US/partner/docs/ios/12_0s/feature/guide/12sobfl.html#wp1025118

Analyzing and Troubleshooting Packets

The PXF engine of the PRE4 is responsible for processing and forwarding packets. As processing 
occurs, PXF counters increment to reflect the internal behavior of the PRE. The router collects this 
statistical information from the counters and appropriately displays it when you enter specific 

show pxf cpu

 commands. The output from these commands is useful in analyzing and troubleshooting 

denied and logged packets. 

To correctly interpret packet statistics, it is important that you understand the behavior of the router 
during packet and access list processing, and the counters that provide the statistical data. This section 
briefly describes access list processing, some PXF counters and their behavior, and some of the 
commands you can use to display statistical information. This section is based on PRE4 with differences 
noted for other PREs.

Access Control Lists

The Cisco 10008 router provides traffic filtering capabilities using Access Control Lists (ACLs). Access 
lists filter network traffic by controlling whether routed packets are forwarded or blocked at the router's 
interfaces. Using ACLs, you can do such things as restrict the contents of routing updates, provide traffic 
flow control, and provide security for your network. 

The Cisco 10008 router supports the following ACL types and features:

•

Standard and extended ACLs

•

Named and numbered ACLs

•

Per-user ACLs

•

Time-based ACLs

The 

access-list

 command is used to configure an ACL. For example, the following configuration creates 

ACL 108:

access-list 108 permit udp any host 10.68.1.10 range 0 5000 log

access-list 108 permit udp host 10.1.1.10 range 0 5000 any log

After creating an ACL, it is applied to an interface using the 

ip access-group

 command. The router 

executes the ACL from top to bottom, denying or permitting packets as directed by the access-list entries 
(ACEs). When the 

log

 keyword is specified in an ACE, the router sends packet information to the 

console.

The last line of an ACL is an implicit deny statement that appears to the router as:

deny any any

Содержание 10008







































































Отзывы:

Нет отзывов